Is there anyway to change the Firepower 2110 to monitor-only mode on the Firepower 2110 and if so, how do I change that via the command line? Thank you! LN
Is there anyway to change the Firepower 2110 to monitor-only mode on the Firepower 2110 and if so, how do I change that via the command line? Thank you! LN
Hello All, I'm trying to setup a DMZ for my client in AWS. I've never done this before and hence the question. I'm planning to use ASAv as the Internet Facing firewall and FTDv/FMCv (Firepower threat Detection virtual and Firepower Management Center...
So, my vFMC is pretty slow, and the more I'm digging as our project moves forward the more annoying that gets. So I googled and found an article (https://www.lammle.com/post/make-cisco-virtual-fmc-drastically-faster-5317/) that makes some sense... I...
What is a good threshold for high cpu on Cisco ASA 5506-x, I don't want to receive a lot of alerts for no reason. Would 90% for more than 10 minutes be a good start? Thanks.
We have a Cisco ASA 5585-x in multi-context mode in our environment. I did a packet capture in one of the contexts and analysed the same on CLI. However, I would like to export it and view the same on Wireshark but my attempts were not successful. I ...
Hi guys, I am confused with what is what. On AWS I want to deploy a FTDv, but on AWS Market its not available, I only have Cisco NGFWv and Cisco FMCv. Is NGFWv and FTDv the same thing? And will I be able to manage the NGFWv using FMCv? What I want i...
Hello, Please can you help I have an Object which i want to remove but every time the ADSM reports it's being used in NAT therefore it cannot be deleted, now I have many over objects using this NAT therefore I cannot delete or believe i can clear N...
how to enable ports in ASA 5585 asdm. Port no 43100, 42100
Hey guys, I have a 3850 stack comprising of two switches. There are 6 VLAN's configured across the stack. I've configured the DG against each of the VLAN interfaces for inter-vlan routing between the VLAN's. From each of the switches within the stac...
I am not able to find documentation for installing a new Cisco FirePOWER Appliance 7120 with an .iso file.Looking forward to help from everyone.
From time to time, we'd receive alerts for retrospective malware events.When we look up the event in FMC, it would only show the timestamps, but no host information.Is this normal/expected?We want to know which host(s) had the malware, so that we can...
I am doing a traceroute to salesforce.com, google.com and I see all the layer hops to my Firewall and then one hop to final destination- which is incorrect. I am not seeing any of the intermediate public hops (and surprisingly not seeing the Do you ...
Hi Everyone,Need to understand the differences between these twodedicated failover link and Stateful Failover link. ThanksMahesh
Hi all, I hope someone can help. I have a small network at a remote site that has suffered a security breach. I need to block all incoming and outgoing internet traffic. The only thing I want to allow is incoming and outgoing traffic for certain IP's...
Hi Where are release notes for 9.4(3)12 ? it's been a few days now and they are still not up?!?!? :( Regards
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-13-2024 02:06 PM | ||
08-08-2024 06:44 PM | ||
08-08-2024 06:24 AM | ||
08-06-2024 09:01 AM | ||
08-05-2024 11:02 PM |
User | Count |
---|---|
9 | |
8 | |
7 | |
4 | |
4 |