On an ASA firewall I have a few cables plugged into ports. No IP addresses are assigned to ports (show interfaces details verifies that). But, a show run verfies that interface vlans have been created with ip addresses assigned.1. Why would the ip no...
Hi all, This may be a silly question but is it possible to downgrade ASA5585-S10-K9 to a K8 versionMany Thanks
Hi,Can someone help me in licensing issue for security context in ASA 5585,We recently purchased a ASA box (5585) which has default security context of 2 and we had like to have 25 context license for this ASA and we got two PAK codes from Cisco for ...
We are setting up Kaspersky to use mobile devices and they request we open 9799, 9899, and 400. I opened those ports on the ASA 5510 but they are still saying closed. One person said we need to set up a NAT outside and then open the ports up under th...
8.2 HI ALL Here is my scenerio and I have worked on this with TAC support over the last month, we finally made progress by getting our ISP to activate the 5 static IPs but here is my issue.basically we have a VOIP phone that is "remote". This phone n...
Hi,I have 2xASA5510 with securityPlus licence.i have confugured 3 context and Active/Active Failover.Everything works fine. But also want to use rometeAccessVPN but couldn't fine anything for VPN. does it support VPN in multiple mode?Could you offer ...
Hi everyoneHope you can help me with this issue.I'm trying to manage an brand new ASA 5525-X with ASDM, the image we have are the following:ASA image: asa861-2-smp-k8.binASDM image: asdm-66114.binthis are the default images that came with the device....
Hi allIf I want to NAT to a pool via a vpn tunnel on my ASA, is this OK?I have done a nat from the original source addresses, destination originalthen translates to source pool of addresses, destination originalDo I base my VPN tunnel phase 2 network...
I see a problem in my Inside Segment of Firewall, where the Primary Firewall is doing Proxy ARP for all directly connected hosts on the Inside Segment.This even causes connectivity issue to the Secondary Firewall IP from the Inside Segment.!interface...
Hi,I have an ASA 5505 firewall. It was requested that when accessing internet, internal users get NAT translated to a public IP. There has to be a one-to-one translation between internal and outside IP addresses. Is it possible to do static NAT tr...
Dear Team , When we see the show ssh sessions on our ASA . it shows output as following K-ASA# show ssh sessionsSID Client IP Version Mode Encryption Hmac State Username0 x.x.x.x 2.0 IN aes25...
Hello, I followed the listed instructions to recover the password for an ASA and after rebooting the ASA I get the rommon #0> prompt.I was wondering if the below procedure is the correct one or if I am doing something wrong. Thanks for you assistan...
Hi Guys,In regards configuring redundant Interface, correct me if i'm wrong from what i understand if I bond two interface(e.g e0/0+e0/1) this will create one logical interface, so regarding the physical Interface does this means that one of them are...
Hi Everyone,For Remote Access VPN here is the current setup--User Connect to the Corp VPN via Internet it first hits the Corp Internet ASA then it connects to the VPN gateway.Say PC connects to VPN gateway IP 150.x.x.x.This IP delongs to VPN gateway...
Hi Everyone,I have configured RA VPN full tunnel.Inside interface of ASA is Vlan1 inside 10.0.0.1 255.255.255.0 CONFIGip local pool 10-pool 10.0.0.51-10.0.0.100 mask 255.255.255.0Need to know is it good des...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 07-09-2025 06:38 AM | ||
| 07-09-2025 06:36 AM | ||
| 07-06-2025 01:40 PM | ||
| 07-04-2025 01:59 AM | ||
| 06-19-2025 07:32 AM |
| User | Count |
|---|---|
| 8 | |
| 7 | |
| 6 | |
| 1 | |
| 1 |
