I have a Site 2 Site VPN set up from my office to my home. One of my applications uses multicast to communicate with a server on the other end of the VPN. Is there anyway I can enable IGMP over my VPN connection??
Hello. I am brand new to Cisco products and have a very BASIC question. The organization I just joined is exclusively Cisco-based, and we have two 890 routers controlling the two branches of our internal network. Both routers are managed through Cisc...
Hi,I was hoping somebody can help me with CISCO ASA programing (version 8.2 (1)) I am trying to set up two things:1. Inboud https access to load balancer that sends the traffic to two exchange servers for OWA, outlook anywhere etc...2. Outbound SMTP ...
Hi Everyone,When i console in to ASA it shows lot of logs messages.I do not get chance to put username and password.Need to know which command i can use to stop logging so when i console to ASA it does not show logging there?RegardsMahesh
Hi Everone,When i type sh run on ASA 5520it gives errorERROR: Command Ignored, Configuration in progress...Any fix other than reboot?RegardsMahesh
Dear cisco my firewall Name cisco asa 5505 .. i given command deny port 80 but now i want to permit this port (80) only for specific ip address ..please help me .access-list 100 extended deny tcp any any eq www access-list 100 extended permit ip an...
I have a ASA 5550 running multiple contexts, but having the AAA authentication serial console (TACACS Server Name) LOCAL allows a tacacs challenge on connecting to the console but I am then unable to issue any commands i.e. enable or Show Run - messa...
Do Cisco Security Manager manage the firewalls of several different customers ?We intend to activate a management service of dozens of ASAs of several clients and I have to be sure that CSM is suitable for this use.Best regardsClaudio
Hello all.I am facing the following issue: I have a layer 3 switch (3560) with multiple VLANs. The ASA (8.3) allowes internet access to only one VLAN at a time. I attempt to configure the ASA 5505 to allow all these VLANs access to the internet.Any h...
Hi, I am having a serious problem, because I have configured all steps to connect ASDM via web browser, but I cannot access ASDM for some unknow reason.I have this configuration but cannot access:http server enabled,http 0.0.0.0 0.0.0.0 insideasdm i...
Hi all,I want one basic firewal which can manage traffic shaping. I am implimenting it in my small office around 15 to 20 users or more. Please suggest me which firewall is suitable for my office?. thanks
I can authenticate through anyconnect and grab the ip address that I set in the vpn pool but I cannot ping any internal host.Internal is 192.168.2.0VPN network is 192.168.5.0I looked at the asa log viewer and it says Asymmetic NAT rules matched for f...
Hi Everyone,I have config both anyconnect and RA split tunnel VPN on the ASA.When using anyconnect client i can connect to Inside network fine but can not access internet sites.I have this ACL to allow only 10.0.0.0 subnet traffic via Anyconnect cli...
Hello,I have an ASA 5505 Sec Plus with ASA 9.1. This firewall has been setup wth a static WAN IP, basic NAT/PAT, ALC's to allow web connectivity, and access to SSH and ASDM enabled. A management PC has been setup with Teamviewer and is directly conne...
HI,can you help me to access DMZ C2 host inside network, i can access from host C1(inside) to DMZ any service.what configuration should be done to permit access from Inside to DMZ and DMZ to Inside for any service...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 08-25-2026 06:22 PM | ||
| 08-24-2026 12:26 AM | ||
| 08-20-2026 05:54 AM | ||
| 08-19-2026 07:59 AM | ||
| 08-10-2026 08:58 AM |
| User | Count |
|---|---|
| 4 | |
| 1 | |
| 1 | |
| 1 | |
| 1 |
