Hi,Can i configure secondary IP addresses and loopback interfaces on a ASA 5520 firewall.Thanks.
Hi,Can i configure secondary IP addresses and loopback interfaces on a ASA 5520 firewall.Thanks.
helloIs there any simulation software for Cisco IPS to make practice implementation? thanks
I have a customer running a redundant ASA 5510 (active/passive) with ASA version 8.3(1). I have a couple of static NAT's for which I have enabled DNS doctoring in the effort of trying to make the users able to browse fx. their Exchange OWA from the i...
I need to propose a diagram to one of our client which has ASA Active/Active ( multiple context ) failover over about 50 KM. geog. dispersed location connected over 1Gb. fiber where each context will be failover to the other context on the other loca...
Can someone tell me whether theASA5510 with the IPS module support HA. That is if one ASA device fails the other will take over instantly. Let me know guys.
Hi,ASA 5510 sec+, os 8.2.Got an ASA in front of a fairly large network. The ASA itself only have one ip, and on vlan interfaces the network is divided into some /24, some /28 and a great deal of /30 networks.One of the vlan interfaces has network 10....
Hello everybody, I am currenlty trying to configure a 871W to forward a port 3389 to the internal address 192.168.1.240. I have been playing with this for a couple days now, and I have not been able to figure out what I am doing wrong. Any help is ap...
All of my IPS have not recieved updaes since the 23rd of December. Are there issues?
Hello,I'm new to cisco products and I just bought a sa520w. I'm upgraded to the latest firmware (1.1.65). I set up a ipv4 rule that allows all communications from the LAN to the DMZ (see below from the backup). It works (e.g. all the protocols I us...
HelloI am trying to figure out how to get the gui ASDM to route my traffic from my wifi router. I have entered a default route statement but does not seem to help resolve the routing issue. I am able to ping from my work station the WIFI router, I ca...
Hello,I installed Cisco IME 7.0.3 on 2 computer with 3G of memory.I have a next error message:Could not verify config username/password [IOEXception - Aythentication failure]when connecting to my devices only from one of this PC I have this erro. Fr...
I have a Cisco 877W router with outer interfaces ATM0 and Dialer0, that use a negotiated ip address that is supplied by my ISP and which is different every time I re-boot the router.I have written ACL's that use domain names rather then static ip's f...
Hello,I have a problem with static PAT when i specify with two ports HTTPS and SMTP for 2 different servers with 1 public IP it does'nt work for SMTP but it only works for HTTPS.Below are the commands:static (DMZ1,outside) tcp X.154.25.X https 172.16...
Hi,I m aware of NAT order of operation but what would be order of operation within the same type of NAT ( e.g. Static policy NAT) e.gaccess-list nat-me permit ip host 192.168.10.1 host 10.0.10.1access-list nat-you permit ip host 192.168.20.1 host 10....
I have a site to site vpn connection using two Pix devices. When I attempt to map a drive on a PC at the remote site to a Server at the main site it does not work. Also, I can not see the PC's on the network accross the VPN tunnel.Help!!!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
06-25-2025 04:32 PM | ||
06-25-2025 04:40 AM | ||
06-20-2025 07:10 AM | ||
06-19-2025 07:32 AM | ||
06-17-2025 01:07 PM |
User | Count |
---|---|
4 | |
4 | |
3 | |
1 | |
1 |