I am pretty new to FTD so they may be a dumb question. I want to setup a FTDv in Azure. I don't have an FMC so I chose the market option to not register with an FMC. The VM deployed as expected, but I have no idea what my next step is. The management...
Forum Posts
A critical vulnerability has been identified in a widely used software application across the network. Please which technical tools and procedures can I employ to coordinate and execute a system wide update to patch this vulnerability?
Hi All, I'm planning to add a new FTD cluster (FP 3140) and manage it through the current FMC which is used to manage 4145 cluster. Can I create the cluster in the FXOS (through Chassis Manager) ? Or it should exclusively be added through FMC? Th...
I have a pair of 4110s, and I had a problem SSHing to the logical ASA's. Having looked at the licensing, it appears that the "Encryption-3DES-AES" is disabled, which is causing it to only accept SSHv1 connections. The problem is, i don't have access ...
Current FMC2500 (v6.6.7) is managing 35 FTD devices (mix of FP11xx, FP21xx, ASA5508-X) 1. is FMCv300 is supported on Azure Cloud? 2. Is migration from FMC2500 to FMCv300 supported? 3. What is the recommended upgrade/migration path? Thanks in advance.
Hi, I'm trying to set up PBR (Route Maps) on FTD managed by FDM but I'm finding it impossible, on ASA it would look something like thisaccess-list ROUTEMAP-ACL1 extended permit tcp object CloudKey1 anyroute-map ROUTEMAP1 permit 10 match ip address R...
Hi All FTD 3105 : the disk /dev/nvme1n1 is unable to be unlocked or reverted with the existing SED key We have a new 3105, displaying the following message. When we proceed it reverts to the same screen. After a couple of reboots, it shows the...
Sorry if this is a dumb question by why does the ASA 5510 have two SPD 0 ports? And does it matter which one I plug the router into? (see image).Thanks in advance!
I am trying to add the no loggin show username command to both our DR-firewall and our Production. I am getting an error when I try to assign it to my production firewall. It already has a FlexConfig Policy assigned to it. Can a device only have one...
Hello,I managed to set up a privilege level 4 with a list of show commands:privilege show level 4 mode exec command access-listwhich allows the user to execute show access-listNow I need to add a line for show ipv6 access-list which I currently don't...
Hi AllI have a S2S VPN connected at phase 1, however doesn't successfully negotiate Phase 2. The issue I have is that my Cisco FTD sits behind a NAT device. I have configured NAT-T.My configuration on my FTD has the local peer configured with the pri...
Hi all, When i try to use my FMC to push update firewall policy to my FTDs running HA, i got the error below."Deployment failed due to major version change on device 6.2.3 to 6.2.3. Unregister the device and re-register." However my production traffi...
Hi Team,We have a requirement to block wildcard domain for example *.xx.xx. As this is wildcard we dont see an option to block it in FTD(Managed using FMC). Please suggest a best way to block this wildcard in FTD. Regards,Sanjay S
Resolved! Upgrade FMC
Hello,I want to upgrade HA FMC that current version is 7.0.6 (build 236) and target is 7.2.5.1.I want to know that my target version is correct and also can I jump from 7.0.6 to 7.2.5.1?Thank you.
Dear Community,i want to deploy the FMC on our Hyper-V Failovercluster. to mange our new Cisco Firepower 3110 Firewall. I followed this Guide: https://www.cisco.com/c/en/us/td/docs/security/firepower/quick_start/fmcv/fpmc-virtual/m_deploy_the_managem...
