HI All we are tying to configure cisco EXpressway E with ASA below is the topology Here the ISP public ip is not static it is a dynanic ip for the SRV record able to manage with DDNS bit for the nat option getting issue with the one way call b...
Forum Posts
hi to alli try to ping to outside interface of VPN concentrator through ASA 5520 via a 3750 switch in between them, but unable to do so.i did the packet trace through the command line and getting following packet-tracer input outside icmp 0 0 8 3....
Resolved! Regarding manual NAT in cisco ASA
I have cisco ASA 5515-x running version 9.2. I want to port forward the request on 80 to 9006 which is of my DVR. I did this : Object network obj-10.10.26.6 host 10.10.26.6 Object network obj-203.156.213.173 host 203.156.213.173 object service po...
I have a new requirement to keep the ASA image & FTD image in the same flatform bundle. Currently, I have 2.4 flatform bundle & it doesn't fulfill my requirement. Does cisco has this feature already in a version or will it be in future road map?
Hey everyone,I am in the middle of an issue from a simple scenario. FW1 -----FW2-----Radius server I set up FW1 to authenticate to the radius server, (FW2 is allowing traffic to/from radius server) aaa-server radserver protocol radiusaaa-server rads...
Is it possible to register FTD to FMC using the FTD's data interface and not the management?
Hello, I am new to the Firepower Threat Defense products. I am trying to set up an external NAT that will forward ports to my internal network. I have tested the NAT rules on high ports such inside-x.x.x.x:8000 <-->outside-x.x.x.x:8000 and it seems...
Resolved! FMC Backup and Copy Failing
I have an FMC running 6.5.0.4 that I can't get to copy to a remote server when the backup completes. I've tried a Windows server running Solarwinds as well a Ubuntu server using Openssh. I've tried confirmed I can ssh from the FMC directly to the s...
What I want to do: Just get notified when vpn tunnels go down or user vpn anyconnect issues..would it be estreamer or syslog?....and where to do it on FTD...
my ASA 5520 (9.1(7) 32) was reset to defaultsIn ASDM, there were no Service Policies (class-map and inspection_default) so I tried to create them with the followingI now have a global-policy and class-default but no inspection_default Not sure what's...
Is Cisco ASA 5510 supported with new anyconnect VPN only, plus & apex license model as the device is end of support and will the licensing be procured per headend even in active standby mode(.i.e.: its 1 license for active and 1 for standby)
Hello All! I'm facing some error for a long time on that device, i cannot solve. I have 2 interfaces: ! interface Vlan20 description Ch.Net nameif CH security-level 100 ip address 192.168.20.1 255.255.255.0 ! interface Vlan172 description Web.N...
Hi there,i am using two firewall Cisco Firepower 2110 as an external internet firewall and 2nd cisco firepower 2130 as an internal Data Center this firewall only used for different VLANs and server-level authentication. External(Internet) firewall is...
Hello Community,I am experiencing a strange behavior with a Dynamic IPSEC VPN Tunnel between an ASA and a IOS router,Both ph1 and ph2 are successful. When I try to ping a local resource in either directions, packets go through the tunnel, decapsulate...
Hardware Info:Cisco Adaptive Security Appliance Software Version 8.0(3)Device Manager Version 6.1(1)ASA5520 Problem:Hi Guys, I am trying to block this VPN attempts to my vpn box but by some reason I am not able to do it. I have already blocked this I...
