Hi experts. I recently got ASA 5516-X for my company and when I switch it off and on again I cant get access to the Inside interface via SSH or ASDM - it does not Ping either. The only way I can get the port to start working again is if I access the ...
Forum Posts
Hi, [FMC 6.2.2] I'm looking for a way to copy rules from a child policy to a parent policy. Egz. I want to copy few rules from child policy 1 to Mother Policy Access Control Mother Policy |__child policy 1 |__child policy 2 How can I do it?Tha...
Hi all; Does Nexus 9000v need special license to be installed for full functionality in the lab environment? I installed 3 of them with basic BGP and basic OSPF works but I got messages while enabling PIM feauture stating that I need to install licen...
Hi,When I am downloading files from internet , it is taking very long time .In the speed test it shows there are enough bandwidth . How can I figure out the problem ( ISP or the asa fw ) till the firewall latency look like normal . How can I troubl...
Hello,I had several A-P 5525X running 9.6(4)12 for the past two years. The SFR modules were running 6.2.3 and were managed by FMC 6.2.3. This week I updated all firewalls from 9.6(4)12 to 9.6(4)30 and then I noticed all SFR modules report: asa01/pri/...
Resolved! ASA SFR Shutdown Procedure
To my knowledge ASA firewall can be shutdown by unplugging the firewall cable, but when SFR runs on SSD hard disk, can I do that? Will it require graceful shutdown?
Hi,Just want to know any reasons why i am unable to access our cisco prime infrastructure 3.6 webpage from LAN subnets but can only access on WiFi subnet.Cisco Prime infrastructure 3.6, Security ManagementAuthentication using our AD - TACACS+ Cisco I...
I'm trying troubleshoot slow excel file transfers, and did my initial investigation by adding a "trust" ACE for that specific subnet which resulted in optimal transfer speeds. I don't see any intrusion events, (the file downloads so I guess it doesn'...
Hi there, we configured and FTD1010 Device with an Passive Interface and attached a Span Port to it. We receive only Broadcast / Multicast Events / Traffic at all in FMC, the whole Unicast Traffic is missing. Any ideas what the problem might be and h...
Hi all, I have a HA pair of ASA 5525 configured as active/standby and installed FirePower on each device.In FMC, i get the error "Interface 'DataplaneInterface0' is not receiving any packets" for the standby device which is normal as it does not rece...
Hi, I hope somebody here can help me. In our company we use Firepower 2120 Firewall with Cisco feeds only (i.e. Cisco-Intelligence-Feed, Cisco-TID-Feed and Cisco-DNS-and-URL-Intelligence-Feed). My personal sites (see below) get blocked with URL Categ...
Hello, I have a customer that has ASA with firepower services. In the summary board of FMC he sees in the "Top Web App Seen" less traffic than he sees in ASA.Also, in the Analysis->Users the users shown are fewer than the actual users in the network...
Resolved! Standby ASA RMA step-by-step
Hello I have a question regarding the RMA process of a standby unit in a ASA cluster. Here are the steps that I have concluded, please correct/add where im wrong: Configure hostname ,Install/Verify boot image and asdm is same as primary.Activate with...
Hello experts,I'm interested to know if on the Cisco ASA there is a way to view the IKE encryption keys. More specifically, I want to do a packet capture in GNS3 (consider this a whitehat experiment) and decrypt IKE_Auth packets which are encrypted w...
Hi I am unable to deploy to Cisco vFTD 6.3.2 or v6.3.0 from Cisco FMC v6.4.0 and I get this error message ... Cisco FMC errorWhen I login to the FTD , The domains.conf file is absent .. I have passed this onto Cisco TAC but no progress ..
