If anyone thinks they can help, please do, I'm desperately trying to help a company with a short term deadline. Just doing it to help out a friend in a rural area where every CISCO tech contact they had seems to be unavailable (For the last and next week) all at once. I'm tearing my hair out! Here's the current ASA configuration:
------------------------------------------------------------------------
ASA Version 7.2(3)
!
hostname [top secret!]
domain-name [top secret!]
enable password [top secret!] encrypted
names
!
interface Vlan1
nameif inside
security-level 100
ip address [top secret!].140 255.255.255.0
!
interface Vlan2
nameif outside
security-level 0
ip address [top secret!].11 255.255.255.248
!
interface Vlan3
shutdown
no forward interface Vlan1
nameif dmz
security-level 50
no ip address
!
interface Ethernet0/0
switchport access vlan 2
!
interface Ethernet0/1
!
interface Ethernet0/2
!
interface Ethernet0/3
!
interface Ethernet0/4
!
interface Ethernet0/5
!
interface Ethernet0/6
!
interface Ethernet0/7
!
passwd [top secret!] encrypted
ftp mode passive
dns server-group DefaultDNS
domain-name [top secret!]
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
access-list inside_nat0_outbound extended permit ip [top secret!] 255.255.255.0 10.0.
8.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 10.0.50.0 255.255.255.24
8
access-list inside_nat0_outbound extended permit ip 10.0.1.0 255.255.255.0 10.0.
6.0 255.255.255.0 – Not in your configuration
access-list outside_1_cryptomap extended permit ip 10.0.1.0 255.255.255.0 10.0.8
.0 255.255.255.0
access-list tr-remote_splitTunnelAcl standard permit any
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit esp any any
access-list outside_access_in extended permit tcp [top secret!] 255.255.255.0 any eq
smtp
access-list outside_2_cryptomap extended permit ip 10.0.1.0 255.255.255.0 10.0.6
.0 255.255.255.0 – Not in your configuration
pager lines 24
logging enable
logging monitor debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
ip local pool remote-vpn 10.0.50.0-10.0.50.7 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image disk0:/asdm-523.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface smtp 10.0.1.201 smtp netmask 255.255.255.2
55
access-group outside_access_in in interface outside – Not in your configuration
route outside 0.0.0.0 0.0.0.0 [top secret!].9 1 – was [top secret!].194 in you config
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
http server enable
http 10.0.6.0 255.255.255.0 inside – Not in your configuration
http 10.0.8.0 255.255.255.0 inside – Outside in your configuration
http 10.0.1.0 255.255.255.0 inside
http 10.0.50.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac – Not in your configuration
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-DES-MD5
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA – Not in your configuration
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs
crypto map outside_map 1 set peer [top secret!].194
crypto map outside_map 1 set transform-set ESP-DES-MD5
crypto map outside_map 2 match address outside_2_cryptomap
crypto map outside_map 2 set pfs
crypto map outside_map 2 set peer [top secret!].162
crypto map outside_map 2 set transform-set ESP-3DES-SHA – Not in your configuration
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 10.0.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
!
!
class-map inspection_default
match default-inspection-traffic
!
!
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
!
service-policy global_policy global
group-policy DfltGrpPolicy attributes
banner none
wins-server none
dns-server none
dhcp-network-scope none
vpn-access-hours none
vpn-simultaneous-logins 3
vpn-idle-timeout none
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec webvpn
password-storage disable
ip-comp disable
re-xauth disable
group-lock none
pfs disable
ipsec-udp disable
ipsec-udp-port 10000
split-tunnel-policy tunnelall
split-tunnel-network-list none
default-domain none
split-dns none
intercept-dhcp 255.255.255.255 disable
secure-unit-authentication disable
user-authentication disable
user-authentication-idle-timeout 30
ip-phone-bypass disable
leap-bypass disable
nem disable
backup-servers keep-client-config
msie-proxy server none
msie-proxy method no-modify
msie-proxy except-list none
msie-proxy local-bypass disable
nac disable
nac-sq-period 300
nac-reval-period 36000
nac-default-acl none
address-pools none
smartcard-removal-disconnect enable
client-firewall none
client-access-rule none
webvpn
functions url-entry
html-content-filter none
homepage none
keep-alive-ignore 4
http-comp gzip
filter none
url-list none
customization value DfltCustomization
port-forward none
port-forward-name value Application Access
sso-server none
deny-message value Login was successful, but because certain criteria have not
been met or due to some specific group policy, you do not have permission to us
e any of the VPN features. Contact your IT administrator for more information
svc none
svc keep-installer installed
svc keepalive none
svc rekey time none
svc rekey method none
svc dpd-interval client none
svc dpd-interval gateway none
svc compression deflate – Not in your configuration
group-policy tr-remote internal
group-policy tr-remote attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value tr-remote_splitTunnelAcl
group-policy staff-remote internal
group-policy staff-remote attributes
dns-server value 10.0.1.200
vpn-tunnel-protocol IPSec
username remote password [top secret!] encrypted privilege 0
username remote attributes
vpn-group-policy [top secret!]
username [top secret!] password [top secret!] encrypted privilege 0
username [top secret!] attributes
vpn-group-policy tr-remote
tunnel-group [top secret!].194 type ipsec-l2l
tunnel-group [top secret!].194 ipsec-attributes
pre-shared-key *
tunnel-group tr-remote type ipsec-ra
tunnel-group tr-remote general-attributes
address-pool remote-vpn
default-group-policy tr-remote
tunnel-group tr-remote ipsec-attributes
pre-shared-key *
tunnel-group [top secret!].162 type ipsec-l2l
tunnel-group [top secret!].162 ipsec-attributes
pre-shared-key *
tunnel-group staff-remote type ipsec-ra
tunnel-group staff-remote general-attributes
address-pool remote-vpn
default-group-policy [top secret!]
tunnel-group [top secret!] ipsec-attributes
pre-shared-key *
prompt hostname context
Cryptochecksum:[top secret!]
------------------------------------------------------------------------
an epic thin client is being set up and the company was simply told to (on their Cisco ASA) enable NAT, with external ip xxx.xxx.xxx.14, internal ip 10.0.xx.xx, and open port 8222.
I went in and added this:
static (inside,outside) xxx.xxx.xxx.58 xxx.xxx.xxx.14 netmask 255.255.255.255
access-list inbound extended permit tcp any host xxx.xxx.xxx.14 eq www
access-list inbound extended permit tcp any host xxx.xxx.xxx.14 eq https
access-list inbound extended permit tcp any host xxx.xxx.xxx.14 eq 8222
access-list inbound extended permit udp any host xxx.xxx.xxx.14 eq 8222
access-group inbound in interface outside
But when we try and run the thin client install, we get an error saying invalid ip/port xxx.xxx.xxx.14/8222.
Please help if you can. I'd be so appreciative. Have already been so thankful for earlier responses.
