Re: How do I enable 2 gigabit interface on ASA5510-sec-bun-k9?

csco11107378 · ‎04-10-2008

hi guys

my ASA5510 has been Security plus licensed, but I cannot find which is gigabit interface. Who can help me enable them, thanks.

ciscoasa# sh version

Cisco Adaptive Security Appliance Software Version 8.0(2)

Device Manager Version 6.0(2)

Compiled on Fri 15-Jun-07 19:29 by builders

System image file is "disk0:/asa802-k8.bin"

Config file at boot was "startup-config"

ciscoasa up 27 mins 10 secs

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 256MB

BIOS Flash M50FW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : CN1000-MC-BOOT-2.00

SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.01

IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04

0: Ext: Ethernet0/0 : address is 001e.f710.6dd8, irq 9

1: Ext: Ethernet0/1 : address is 001e.f710.6dd9, irq 9

2: Ext: Ethernet0/2 : address is 001e.f710.6dda, irq 9

3: Ext: Ethernet0/3 : address is 001e.f710.6ddb, irq 9

4: Ext: Management0/0 : address is 001e.f710.6ddc, irq 11

5: Int: Not used : irq 11

6: Int: Not used : irq 5

Licensed features for this platform:

Maximum Physical Interfaces : Unlimited

Maximum VLANs : 100

Inside Hosts : Unlimited

Failover : Active/Active

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 2

GTP/GPRS : Disabled

VPN Peers : 250

WebVPN Peers : 2

Advanced Endpoint Assessment : Disabled

This platform has an ASA 5510 Security Plus license.

Serial Number: JMX1214L0JQ

Running Activation Key: 0x98015a60 0x3c8f8022 0xd401a5b0 0x80704c60 0x0401b488

Configuration register is 0x1

Configuration has not been modified since last system restart.

ciscoasa#

ciscoasa# sh int ip b

Interface IP-Address OK? Method Status Protocol

Ethernet0/0 unassigned YES unset administratively down down

Ethernet0/1 unassigned YES unset administratively down down

Ethernet0/2 unassigned YES unset administratively down down

Ethernet0/3 1.1.1.2 YES CONFIG up up

Management0/0 192.168.1.1 YES CONFIG down down

ciscoasa#

vitripat · ‎04-11-2008

Ethernet0/0 and Ethernet0/1 can be configured as gigabit ports. You can set the speed of these interfaces using the speed command in interface configuration mode.

Please note that interface would still show as "Ethernet0/0" & "Ethernet0/1", but speed can be set to 1000Mbps. This feature was added from 7.2(3) code. Here is a link for the same-

http://www.cisco.com/en/US/docs/security/asa/asa72/release/notes/asarn723.html#wp272663

Hope that helps.

Regards,

Vibhor.

csco111107378 · ‎04-11-2008

Thank you very much.

torex-hiscom · ‎07-10-2008

Hi Vibhor,

I was trying this too on my 5510 with security plus license, but it doesn't recognize the "speed 1000" command.

I'm running version 8.0.2.

I obtained this hardware in the end of 2005.

Regards,

Albert Bruggeman

csco11107378 · ‎07-10-2008

this feature supported from 7.2.3 and 8.0.3

torex-hiscom · ‎07-10-2008

Oh, I didn't realize that!

I thought 8.0.2 had the features of 7.2.3 but that's not true of course.

Thank you.

Regards