09-04-2011 09:44 PM - edited 03-10-2019 05:28 AM
hi experts,
Could someone please help me on resetting password on my IPS module below provided are the HW details. from the below out put we can see that I dont have option to reset password by using hw-module module 1 pass commnad.
XX sh ver
Cisco Adaptive Security Appliance Software Version 7.0(7)
Device Manager Version 5.0(9)
Compiled on Fri 06-Jul-07 10:37 by builders
System image file is "disk0:/asa707-k8.bin"
Config file at boot was "startup-config"
up 144 days 17 hours
Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)
Boot microcode : CNlite-MC-Boot-Cisco-1.2
SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Ext: Ethernet0/0 : address is 0007.0e11.dc20, irq 9
1: Ext: Ethernet0/1 : address is 0007.0e11.dc21, irq 9
2: Ext: Ethernet0/2 : address is 0007.0e11.dc22, irq 9
3: Ext: Not licensed : irq 9
4: Ext: Management0/0 : address is 0007.0e11.dc24, irq 11
5: Int: Internal-Data0/0 : address is 0000.0001.0002, irq 11
6: Int: Internal-Control0/0 : address is 0000.0001.0001, irq 5
Licensed features for this platform:
Maximum Physical Interfaces : 4
Maximum VLANs : 10
Inside Hosts : Unlimited
Failover : Disabled
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Security Contexts : 0
GTP/GPRS : Disabled
VPN Peers : 50
This platform has a Base license.
Serial Number: JMX1140L0S7
Running Activation Key: 0x18174b71 0x1017f59b 0xac800d50 0xbc1034e0 0x0726b8a8
Configuration register is 0x1
Configuration last modified by netadmin at 06:53:08.925 UTC Thu May 26 2011
l
XX sh module
Mod Card Type Model Serial No.
--- -------------------------------------------- ------------------ -----------
0 ASA 5510 Adaptive Security Appliance ASA5510 JMX1140L0S7
1 ASA 5500 Series Security Services Module-10 ASA-SSM-10 JAF1342AJBR
Mod MAC Address Range Hw Version Fw Version Sw Version
--- --------------------------------- ------------ ------------ ---------------
0 0007.0e11.dc20 to 0007.0e11.dc24 2.0 1.0(11)2 7.0(7)
1 0026.cba2.ae61 to 0026.cba2.ae61 1.0 1.0(11)5 7.0(2)E4
Mod Status Data Plane Status
--- ------------------ ---------------------
0 Up Sys Not Applicable
1 Up Up
# hw
# hw-module m
# hw-module module 1 ?
recover Configure recovery of this module
reload Reload the module
reset Reset the module
shutdown Shut down the module
# hw-module module 1
Solved! Go to Solution.
09-04-2011 11:48 PM
Cheers, let me know if you have any further questions.
09-04-2011 10:12 PM
The AIP module password recovery to be performed from the ASA is only supported from ASA version 7.2.2:
Command: hw-module module password-reset
Here is the command for your reference:
http://www.cisco.com/en/US/docs/security/asa/asa80/command/reference/gh.html#wp1761289
Since you are currently running ASA version 7.0.7, you would need to perform the AIP module password recovery by reimaging the AIP module, and unfortunately you would lose all the configuration via this method:
It's probably easier to upgrade the ASA to version 7.2.2 and recover the AIP module password via the command line.
Hope this helps.
09-04-2011 11:12 PM
thanks a lot, I would probably upgrade the ASA version to
asa723-k8.bin, hope direct upgrade would work
thanks
09-04-2011 11:16 PM
Great, and thanks for the update. Pls kindly mark the post as answered if you have no further question, so others can learn from your post. Thank you.
09-04-2011 11:45 PM
Thanks and appreciated
I believe u meant to click on correct answer rit ? I will do it for sure once I complete the task which is on coming thursday.
Thanks
09-04-2011 11:48 PM
Cheers, let me know if you have any further questions.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide