06-16-2011 06:27 AM - edited 03-11-2019 01:46 PM
Hi,
I have an ASA 5510 and I can not configure fine.
My problem is that I have 10 public address connected to ASA and each public address is redirectioned to an internal IP address.
An of these public address is the ip address of mi ASA.
I need help for configure and access-list and an NAT, the others I will configure.
interface Ethernet0/0
description Interface_WAN_World-Ttrends
speed 100
duplex full
nameif outside
security-level 0
ip address 84.88.36.3 255.255.254.0
!
interface Ethernet0/1
description Interface_LAN_Ttrends-World
speed 100
duplex full
nameif inside
security-level 100
ip address 10.0.0.252 255.255.254.0
!
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
Thanks
Solved! Go to Solution.
06-27-2011 07:54 AM
Hi Daniel,
Could you try as given in the following document and let me know if you can access 10.0.0.156?
Let me know.
Regards,
Anu
06-27-2011 08:06 AM
Hi,
I activated this command but there are any entry with ip address 84.88.36.10
can I have a problem with my router ISP? Do I have to call to my ISP for clear your ARP table?
If you want You can connect via Webex :-P!!!
Thanks
06-27-2011 08:10 AM
Hi Daniel,
The document i provided is what you can do from your side. If you can call your ISP and ask them to clear the arp cache, that's much better.
Regards,
Anu
06-27-2011 08:14 AM
Eiissssss!!
I follewed your document and i change the IP addres of my ASA to 84.88.36.12 (an IP doesn't work) and after I change it to the original IP address.
Now, all work fine!!!!!
But now, inside my network can not access to this IP publics! What happens?
Thanks!!!
06-27-2011 08:17 AM
That's great Daniel!!
For the inside access, do the following:
static (inside, inside)
same-security-traffic permit intra interface
Let me know!
Regards,
Anu
P.S. Do rate posts that were helpful to you.
06-29-2011 08:48 AM
Hi,
I have configured four new rules and all work fine!!!!!
But, I can not access to public IP address from inside my network.
I have configured these commands:
static (inside,inside) 10.0.0.30 84.88.36.7 netmask 255.255.255.255
same-security-traffic permit intra-interface
But doesn't work.
Thanksss!!
06-30-2011 01:13 AM
Hi Daniel,
Are you using the IP address 84.88.36.7 or a hostname? Is the IP 10.0.0.30 reachable from the inside network?
Let me know.
Regards,
Anu
07-01-2011 03:30 AM
Hi,
I am using a IP address and Yes, I have access to my internal IP address 10.0.0.30 inside my network.
Thanks
Daniel Garzón
07-01-2011 03:50 AM
Hi Daniel,
It should be:
static (inside,inside) 84.88.36.7 10.0.0.30 netmask 255.255.255.255
and not
static (inside,inside) 10.0.0.30 84.88.36.7 netmask 255.255.255.255
I'm sorry i overlooked this part.
Let me know if this resolves the issue.
Regards,
Anu
07-01-2011 04:20 AM
I hate ASAaaa!!!
I configured these (with other internal IP, sorry, i have DHCP)
static (inside,inside) 84.88.36.7 10.0.0.52 netmask 255.255.255.255
same-security-traffic permit intra-interface
Doesn't work.
Grrr!!
07-01-2011 11:51 PM
Hi Daniel,
Could you add the following?
global (inside) 1 interface
let me know.
regards,
Anu
07-04-2011 01:07 AM
Ohhhhh my goddddd!!!!!
You are my idol!!!! Now, all work fine.
Thanks a lot.
07-04-2011 01:22 AM
Hi,
I'm sorry. I speak very quickly. I was acceding to another public ip addres. Sorry!!!
What I can do more?
07-04-2011 02:41 AM
Hi Daniel,
So which one works and which one doesn't? Or is the public IP still not reachable from the inside network?
Regards,
Anu
07-04-2011 03:28 AM
Hi,
All public IP addresses configured in ASA are still not reachable from the inside network.
Thanks
Regards,
Daniel Garzón.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide