Solved: No image found even uploding the image by rommon mode

Mannisidhu · ‎09-22-2017

As i uploaded the ios on flash but it is still goin on to rommon mode as it also shows me while booting that "booting image not found

rommon #1> rommon #0> confreg
Invalid or incorrect command. Use 'help' for help.
rommon #1>
rommon #1> Current Configu
Invalid or incorrect command. Use 'help' for help.
rommon #1> Summary: boot Rnetbootfails
Invalid or incorrect command. Use 'help' for help.
rommon #1> pas NVRAM fie ? yn [n]: y
Invalid or incorrect command. Use 'help' for help.
rommon #1> eable boot o ROMable syste configuraion? y/n []: n
Invalid or incorrect command. Use 'help' for help.
rommon #1> go toROMMON propbootmode? y/n n]: y
Invalid or incorrect command. Use 'help' for help.
rommon #1> disale displayofatin Register 0x0010200
Invalid or incorrect command. Use 'help' for help.
rommon #1> Configuraion Sumcs in auo-bootloadr mode
Invalid or incorrect command. Use 'help' for help.
rommon #1>
rommon #1> Upate ConfigReg
Invalid or incorrect command. Use 'help' for help.
rommon #1> update
Invalid or incorrect command. Use 'help' for help.
rommon #1> confeg
Invalid or incorrect command. Use 'help' for help.
rommon #1> confreg

Current Configuration Register: 0x00102000
Configuration Summary:
boot ROMMON
load ROMMON if netboot fails
pass NVRAM file specs in auto-bootloader mode

Do you wish to change this configuration? y/n [n]: y
enable boot to ROMMON prompt? y/n [n]: y
select specific Flash image index? y/n [n]: n
disable system configuration? y/n [n]: n
go to ROMMON prompt if netboot fails? y/n [n]: y
enable passing NVRAM file specs in auto-boot mode? y/n [n]: y
disable display of BREAK or ESC key prompt during auto-boot? y/n [n]: n

Current Configuration Register: 0x00102000
Configuration Summary:
boot ROMMON
load ROMMON if netboot fails
pass NVRAM file specs in auto-bootloader mode

Update Config Register (0x102000) in NVRAM...

rommon #2>

boot
Launching BootLoader...
Default configuration file contains 1 entry.

Searching / for images to boot.

No images in /
Error 15: File not found

unable to boot an image

Default configuration file contains 1 entry.

Searching / for images to boot.

No images in /
Error 15: File not found

unable to boot an image

Failsafe booting engaged.
Default configuration file contains 1 entry.

Searching / for images to boot.

No images in /
Error 15: File not found

unable to boot an image

CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45

Low Memory: 632 KB
High Memory: 507 MB
PCI Device Table.
Bus Dev Func VendID DevID Class              Irq
00 01 00   1022   2080 Host Bridge
00 01 02   1022   2082 Chipset En/Decrypt 11
00 0C 00   1148   4320 Ethernet           11
00 0D 00   177D   0003 Network En/Decrypt 10
00 0F 00   1022   2090 ISA Bridge
00 0F 02   1022   2092 IDE Controller
00 0F 03   1022   2093 Audio              10
00 0F 04   1022   2094 Serial Bus         9
00 0F 05   1022   2095 Serial Bus         9

Evaluating BIOS Options ...
Launch BIOS Extension to setup ROMMON

Cisco Systems ROMMON Version

Kornelia Gutierrez · ‎09-22-2017

Hello,

Can you please describe what process did you follow when you uploaded the image?

Have you tried the following:

https://www.cisco.com/c/en/us/support/docs/routers/1600-series-routers/6301-rommon-boot-image.html

or loading the image using rommon

rommon #0> ADDRESS=x.x.x.x   --- where x.x.x.x ip address you will assing to ASA
rommon #1> SERVER=y.y.y.y    ---where y.y.y.y ip address of the tftp server
rommon #2> IMAGE=asaimage    ---where asaimage is the image of the ASA you want to upload
rommon #3> ping y.y.y.y      --- testing connectivity between ASA and tftp  server
rommon #4>tftp               --- command used to upload the image into ASA
 

View solution in original post

Mannisidhu · ‎09-22-2017

Hi all

Looking forward to hear from you. Kindly suggest

Kornelia Gutierrez · ‎09-22-2017

Hello,

Can you please describe what process did you follow when you uploaded the image?

Have you tried the following:

https://www.cisco.com/c/en/us/support/docs/routers/1600-series-routers/6301-rommon-boot-image.html

or loading the image using rommon

rommon #0> ADDRESS=x.x.x.x   --- where x.x.x.x ip address you will assing to ASA
rommon #1> SERVER=y.y.y.y    ---where y.y.y.y ip address of the tftp server
rommon #2> IMAGE=asaimage    ---where asaimage is the image of the ASA you want to upload
rommon #3> ping y.y.y.y      --- testing connectivity between ASA and tftp  server
rommon #4>tftp               --- command used to upload the image into ASA
 

Mannisidhu · ‎09-22-2017

Hi Kornelia

I used the same process as mentioned by you. Thanks for reply

nasaru123 · ‎03-24-2018

Dear,

could you please help me resolve this problem..?

I'm using Cisco 819-HG-4G-G-K9 Router, Due to Full disk we try to Format Secondary disk to get some disk space ,but accidentally we choose main flash:0 memmory.. now there is no ios or bootLDR in flash...

i try to connect through xmodem and also tftpdnld ...but no response ...!

the followed steps which i have done to troubleshoot i'm mentioning below.. and please help me to solve this issue..!

1--------------------------------------------------

rommon 8 > sysret

System Return Info:

count: 19, reason: reset

pc:0x0, error address: 0x0

Stack Trace:

FP: 0x00000000, PC: 0x00000000

--------------------------------------------------------------

rommon 11 > context

No context available

rommon 5 > rommon-pref

usage: rommon-pref [readonly|upgrade]

rommon 6 > showmon

Last Reset Reason: System Reset

---------------------------------------------------------------------

rommon 2 > showmon

Last Reset Reason: System Reset

ReadOnly ROMMON version is:

System Bootstrap, Version 15.2(2r)T1, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

No upgrade ROMMON version present

ReadOnly ROMMON currently running

ReadOnly ROMMON is selected for next boot

-----------------------------------------------------------------

rommon 3 > meminfo

-----------------------------------------------------

Current Memory configuration is:

On-board: Size = 1024 MB : Start Phy Addr = 0x0_00000000

-----------------------------------------------------

Main memory size: 1024 MB in 32 bit mode.

Available main memory starts at 0x1008000, size 1032160KB

Smart Init is enabled.

NVRAM size: 256 KB

Manufacturer's JEDEC ID code:

On-board: JDEC ID is not available

------------------------------------------------------------------------------

rommon 25 > set

PS1=rommon ! >

RTC_STAT=0

LICENSE_BOOT_LEVEL=

FE_SPEED_MODE=4

FE_PORT=0

TFTP_RETRY_COUNT=20

WARM_REBOOT=FALSE

RELOAD_TYPE=1

IP_ADDRESS=192.168.10.2

IP_SUBNET_MASK=255.255.255.0

DEFAULT_GATEWAY=192.168.10.1

TFTP_SERVER=192.168.10.45

TFTP_FILE=c800-universalk9-mz.SPA.153-3.M4.bin

FE0_PORT=AUTO

?=0

BSI=0

RANDOM_NUM=1491046230

RET_2_RTS=06:05:53 UTC Sat Mar 17 2018

RET_2_RCALTS=1521266744

rommon 4 > unset bootflash:

unset: "bootflash:" does not exist

rommon 5 > xmodem -c c800-universalk9-mz.SPA.153-3.M4.bin

monitor: command "xmodem" not found

---------------------------------------------------------------------------

rommon 1 > boot flash:

program load complete, entry point: 0x4000000, size: 0x18c40

boot: cannot determine first executable file name ondevice "flash:"

rommon 4 > dir flash:

program load complete, entry point: 0x4000000, size: 0x18c40

Directory of flash:

Kindly please support anyone..