07-21-2003 01:55 PM - edited 02-20-2020 10:52 PM
I tried taking a PIX 501 config, and installing it on a 506E, this did not work. I could not pass traffic in or out of the PIX (translation did not work). Should this be that case? The config works fine on the 501. Below is the config.
Thanks
nameif ethernet0 outside security0
nameif ethernet1 inside security100
hostname FW
domain-name domain.com
fixup protocol ftp 21
fixup protocol http 80
fixup protocol h323 1720
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sqlnet 1521
fixup protocol sip 5060
fixup protocol skinny 2000
fixup protocol domain 53
no fixup protocol smtp 25
names
access-list 101 permit icmp any any echo-reply
access-list 101 permit icmp any any time-exceeded
access-list 101 permit icmp any any unreachable
access-list 101 permit ip 10.1.1.0 255.255.255.0 10.1.1.0 255.255.255.0
pager lines 24
interface ethernet0 auto
interface ethernet1 auto
mtu outside 1500
mtu inside 1500
ip address outside xxx.xxx.xxx.232 255.255.255.224
ip address inside 10.1.1.2 255.255.255.0
ip verify reverse-path interface outside
ip audit info action alarm
ip audit attack action alarm
ip local pool VPNpool 10.1.1.251-10.1.1.254
pdm location 10.1.1.0 255.255.255.0 inside
pdm history enable
arp timeout 1800
global (outside) 1 xxx.xxx.xxx.233 netmask 255.255.255.224
nat (inside) 0 access-list 101
nat (inside) 1 10.1.1.0 255.255.255.0 0 0
static (inside,outside) xxx.xxx.xxx.228 SERVERWEB netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.240 SERVERDCEXC netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.234 VPN-PPTP-Out1 netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.235 VPN-PPTP-Out2 netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.236 VPN-PPTP-Out3 netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.237 VPN-PPTP-out4 netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.231 SERVER-Open-FTP netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.238 Carpediem netmask 255.255.255.255 0 0
static (inside,outside) xxx.xxx.xxx.229 SERVERDCEXC netmask 255.255.255.255 0 0
conduit permit tcp host xxx.xxx.xxx.229 eq smtp any
conduit permit tcp host xxx.xxx.xxx.240 eq smtp any
conduit permit tcp host xxx.xxx.xxx.229 eq www any
conduit permit tcp host xxx.xxx.xxx.229 eq 443 any
conduit permit tcp host xxx.xxx.xxx.240 eq www any
conduit permit tcp host xxx.xxx.xxx.228 eq www any
conduit permit tcp host xxx.xxx.xxx.228 eq ftp any
conduit permit tcp host xxx.xxx.xxx.231 eq ftp any
conduit permit tcp host xxx.xxx.xxx.238 eq www any
conduit permit tcp host xxx.xxx.xxx.238 eq 443 any
conduit permit icmp any any echo-reply
conduit permit gre any any
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.225 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h323 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
http server enable
http 10.1.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community n0publ1c
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
no sysopt route dnat
crypto ipsec transform-set myset esp-des esp-md5-hmac
crypto dynamic-map dynmap 10 set transform-set myset
crypto map mymap 10 ipsec-isakmp dynamic dynmap
crypto map mymap client configuration address initiate
crypto map mymap client configuration address respond
crypto map mymap interface outside
isakmp enable outside
isakmp key mykey address 0.0.0.0 netmask 0.0.0.0
isakmp identity address
isakmp client configuration address-pool local VPNpool outside
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption des
isakmp policy 10 hash md5
isakmp policy 10 group 1
isakmp policy 10 lifetime 86400
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption des
isakmp policy 20 hash sha
isakmp policy 20 group 1
isakmp policy 20 lifetime 86400
vpngroup vpn-all idle-time 1800
telnet 10.1.1.0 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
vpdn group 1 accept dialin pptp
vpdn group 1 ppp authentication pap
vpdn group 1 ppp authentication chap
vpdn group 1 ppp authentication mschap
vpdn group 1 ppp encryption mppe auto
vpdn group 1 client configuration address local VPNpool
vpdn group 1 client configuration dns 10.1.1.9 207.217.120.83
vpdn group 1 client configuration wins 10.1.1.9
vpdn group 1 pptp echo 60
vpdn group 1 client authentication local
vpdn username xxx password
vpdn username yyy ssssss password
vpdn enable outside
vpdn enable inside
terminal width 80
07-21-2003 10:17 PM
Hi,
Normally configurations are exchangable, so, have you tried the clear xlate command?
Are your interfaces up?
Send some of the logging output which shows what happens, maybe we can help you.
Kind Regards,
Leo
07-23-2003 11:01 AM
Thanks for the reply,
-I cleared XLATE and ARP tables
-Both interfaces were up, as I was able to ping them fron the inside and outside (sho int also showed them as up)
Unfortunately I do not have logging output. However does the below message mean anything?
Global XXX.XXX.XXX.233 will be Port Address Translated
WARNING: access-list protocol or port will not be used
07-23-2003 11:13 AM
Hi -
Try getting your conduits changed over to ACL's as conduits and ACL's are known not to work together. Basically, ACL's will be used over conduits.
Hope this helps -
07-23-2003 12:34 PM
The warning message you get is because of your nat 0 command in place which points to an access-lists which does not have ip only statements in it, but also icmp. These rules are not used while an access-list is bound to the nat 0, in case an access-list is bound to the nat 0 command, you should only use ip permit and ip deny on this access-list (the PIX will just ignore other protocol rules)
Besides that, you have to get rid of the conduit commands, instead of conduits, use access-lists bounded to the appropiate interface. The use of conduits is not recommended anymore.
Hope this helps,
Leo
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide