cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1884
Views
0
Helpful
3
Replies

Subinterface doesn't respond to pings - NP Identity ifc

kerry-davis
Level 1
Level 1

I'm trying to set up an 802.1 q trunk between my layer 3 switch and ASA5520.  I understand I need to create a subinterface to accomplish this and have done so.  However, the subinterface does not respond to pings, and when I attempt to run the packet tracer on the firewall itself, I get a message saying Flow is denied by configured rule.  But the strange thing is it shows the output interface as "np identity ifc":

New Picture.png

(The VLAN in question is VLAN2 192.168.2.3 is the VLAN2 address on the switch).  The ASA config is as follows:

:

ASA Version 8.2(5) <context>

!

hostname context2

names

!

interface GigabitEthernet0/0.2

nameif Inside0/0.2

security-level 20

ip address 192.168.2.1 255.255.255.0 standby 192.168.2.2

!

interface Outside

nameif Outside

security-level 40

ip address 157.142.246.132 255.255.255.0 standby x.x.246.134

!

interface Management

nameif Management

security-level 100

ip address 192.168.4.2 255.255.255.0 standby 192.168.4.4

management-only

!

interface GigabitEthernet0/0

no nameif

no security-level

no ip address

!

pager lines 24

mtu Outside 1500

mtu Management 1500

mtu Inside0/0.2 1500

no monitor-interface Outside

no monitor-interface Management

icmp unreachable rate-limit 1 burst-size 1

no asdm history enable

arp timeout 14400

route Outside 0.0.0.0 0.0.0.0 x.x.246.1 1

timeout xlate 3:00:00

timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02

timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00

timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00

timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute

timeout tcp-proxy-reassembly 0:01:00

timeout floating-conn 0:00:00

http server enable

http 192.168.0.0 255.255.0.0 Management

http 192.168.0.0 255.255.0.0 Inside0/0.2

no snmp-server location

no snmp-server contact

telnet 192.168.0.0 255.255.0.0 Management

telnet 192.168.0.0 255.255.0.0 Inside0/0.2

telnet timeout 5

ssh timeout 5

no threat-detection statistics tcp-intercept

!

class-map inspection_default

match default-inspection-traffic

!

!

policy-map type inspect dns preset_dns_map

parameters

message-length maximum client auto

message-length maximum 512

policy-map global_policy

class inspection_default

inspect dns preset_dns_map

inspect ftp

inspect h323 h225

inspect h323 ras

inspect ip-options

inspect netbios

inspect rsh

inspect rtsp

inspect skinny

inspect esmtp

inspect sqlnet

inspect sunrpc

inspect tftp

inspect sip

inspect xdmcp

!

service-policy global_policy global

: end

3 Replies 3

jhampt20_ford
Level 1
Level 1

The sub-interface needs a vlan id, something like:

interface GigabitEthernet0/0.2

vlan 2

nameif Inside0/0.2

security-level 20

ip address 192.168.2.1 255.255.255.0 standby 192.168.2.2

!

Also on the switch dont forget to create vlan 2, than double check that it is allowed to cross the trunk.

Thanks for the reply.

A bit more info - the ASA is part of an active/active pair, and from what I understand, the VLAN can only be set at the system level.  I have done this for int gigabitethernet0/0.2 in the system config (VLAN2), but for some reason when I show the config at the context level it does not show the VLAN.

Also, I have confirmed the switchport is set for 802.1q trunking and VLAN 2 is allowed.

Is there something else I need to do to make sure the VLAN assignment is applied at the context level on the ASA?  Also, would this prevent the packet tracer from pinging the interface from the same subnet?

A little stumped here.

eric.lovelace
Level 1
Level 1

Bump...Any resolution? I have the exact same issue.

Review Cisco Networking for a $25 gift card