WS -SVC -FWM -1

[iec1128759]

I have a problem with the card Hardware: WS -SVC -FWM -1

Currently has the version

FWSM Firewall Version 2.3 (4 )

FWSM Device Manager Version 4.1 (5 )

The problem is that I can not enable the interfaces

Interface eobc " eobc " , is up , line protocol is up

MAC address 0000.1100.0000 , MTU 1500

127.0.0.11 IP address , subnet mask 255.255.255.0

Received 1267 packets , 85666 bytes

Transmitted 2932 packets , 123535 bytes

Dropped 0 packets

< --- More --- >

Control Point Interface States :

Interface number is 0

Interface config status is active

Interface state is active

Control Point States :

Interface vlan config status is not active

Interface vlan state is DOWN

Vlan8 Interface " " , is administratively down , line protocol is up

Available but not configured via nameif

Vlan9 Interface " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface Vlan11 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan12 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan13 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan14 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan15 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan16 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan17 " " , is administratively down , line protocol is up

< --- More --- >

Available but not configured via nameif

Interface vlan18 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan19 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface VLAN20 " " , is administratively down , line protocol is up

Available but not configured via nameif

Interface vlan24 " " , is administratively down , line protocol is up

Available but not configured via nameif

Can anyone tell me how I can update it since the pictures went up to the switch,

I think that's why I can not enable the interfaces

I hope I can help.

regards

[iec1128759]

FWSM#

FWSM#

FWSM# copy tftp://100.100.100.1/c6svc-fwm-k9.3-1-5.bin flash:image

copying tftp://100.100.100.1/c6svc-fwm-k9.3-1-5.bin to flash:image

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Received 5865984 bytes.

imgsum_config: sumval(0x9c65) md5(0xe682806c 0xcc464766 0xaf0a1317 0x40b5ed11)

imgsum_verify: chksum(0x   0) md5(0x0c127e10 0x17221e4c 0xe981d516 0x18cc85f7)

Checksum verification on new image failed.

Image not installed.

FWSM#

[rfalconer.sffcu]

You have to assign a nameif to each of the vlan interfaces for them to be enabled. Just like the inside and outside, you need to put the nameif on each one.