This is the procedure to copy the running configuration from a Cisco IOS router to a TFTP server:
Create a row in the ccCopy Table, and set the necessary values for the attributes. Initiate the transfer process, as shown:
snmpset -v 2c -c .22.214.171.124.126.96.36.199.188.8.131.52.1.2. i 1
.184.108.40.206.220.127.116.11.18.104.22.168.1.3. i 4
.22.214.171.124.126.96.36.199.188.8.131.52.1.4. i 1
.184.108.40.206.220.127.116.11.18.104.22.168.1.5. a ""
.22.214.171.124.126.96.36.199.188.8.131.52.1.6. s ""
.184.108.40.206.220.127.116.11.18.104.22.168.1.14. i 4
Check for the completion of transfer process, as shown:
snmpwalk -v 2c -c .22.214.171.124.126.96.36.199.188.8.131.52.1.10.
Repeat the command until the state is successful.
Destroy the row created, as shown:
snmpset -v 2c -c .184.108.40.206.220.127.116.11.18.104.22.168.1.14. i 6
These are examples of each step:
Cisco IOS Router Name/IP Address: 10.0.0.1
Server IP Address: 10.0.0.2
File Name: Router.cfg
SNMP Read Write Community String: private
Random Row number:50
Creating a row in the ccCopy Table, setting the necessary values of the attributes (protocol, source file type, destination file type, server address, file name), and initiating the transfer.
snmpset -v 2c -c private 10.0.0.1 .22.214.171.124.126.96.36.199.188.8.131.52.1.2.50 i 1
.184.108.40.206.220.127.116.11.18.104.22.168.1.3.50 i 4
.22.214.171.124.126.96.36.199.188.8.131.52.1.4.50 i 1
.184.108.40.206.220.127.116.11.18.104.22.168.1.5.50 a "10.0.0.2"
.22.214.171.124.126.96.36.199.188.8.131.52.1.6.50 s "Router.cfg"
.184.108.40.206.220.127.116.11.18.104.22.168.1.14.50 i 4
2. Checking the transfer status. Repeat checking until the status is successful.
client=====[router1]====[router2]====[router3]=====[router4-gre/tunnel ]===[gre/tunnel router5]===server What is the best way to troubleshoot/identify which router in this path is blocking a udp response from the server to the client? I am able ...
Hello Community. I have Cisco 1552s industrial deployed in my environment running two SSIDs. The SSID's are broadcasted by the 1552S access points. The issue is even after getting DHCP IP from server mobile devices cannot go out to internet.We are using 5...
Hello All im experiencing a problem with some computers dropping IP the addresswith a release / renew the computer is getting a new ip from the dhcp server and after 5 minutes just goes down and doenst repond any more in the arp table is s...
We have two 4500-X layer 3 switches, one at each location running EIGRP and Layer 2. There are two connections between the 4500's that are trunk lines. We have about 30 VLANs, all of them are within the 10.x.x.x range. We have routing enabled, EIGRP is se...