Description of the issue
Multicast Receivers are unable to receive traffic initiated by the Multicast source.
Verify if your device configuration matches the following configuration.
##### FE1 ########
ip routing
ip multicast-routing vrf Engineering
ip pim vrf Engineering rp-address 200.2.3.100
ip pim vrf Engineering register-source Loopback500
!
interface Loopback0
description Fabric Node Router ID
ip address 70.0.0.1 255.255.255.255
ip router isis
!
vrf definition Engineering
rd 1:4099
!
address-family ipv4
route-target export 1:4099
route-target import 1:4099
exit-address-family
!
interface Vlan1021
mac-address 0000.5000.5000 < ---- Anycast MAc for gateway
vrf forwarding Engineering
ip address 100.1.1.1 255.255.255.0 <---- Anycast Gateway IP
ip pim sparse-dense-mode
no lisp mobility liveness test
lisp mobility v4eid
!
interface Loopback500
vrf forwarding Engineering
ip address 153.3.3.3 255.255.255.255
ip pim sparse-mode
end
!
router lisp
locator-set rloc_set1
IPv4-interface Loopback0 priority 10 weight 10
auto-discover-rlocs
exit-locator-set
!
service ipv4
encapsulation vxlan
map-cache-limit 5119
database-mapping limit dynamic 3000
itr map-resolver 71.0.0.1
etr map-server 71.0.0.1 key key1
etr map-server 71.0.0.1 proxy-reply
etr
sgt
proxy-itr 70.0.0.1
use-petr 71.0.0.1
exit-service-ipv4
!
instance-id 4097
remote-rloc-probe on-route-change
service ipv4
eid-table default
exit-service-ipv4
!
exit-instance-id
!
instance-id 4099
remote-rloc-probe on-route-change
dynamic-eid v4eid
database-mapping 100.1.0.0/16 locator-set rloc_set1
exit-dynamic-eid
service ipv4
eid-table vrf Engineering
database-mapping 153.3.3.3/32 locator-set rloc_set1 < — To register the address used by PIM source to the LISP MS/MR
map-cache 0.0.0.0/0 map-request
exit-service-ipv4
!
exit-instance-id
!
ipv4 locator reachability exclude-default
ipv4 source-locator Loopback0
exit-router-lisp
!
interface LISP0.4099
ip pim sparse-mode
!
##### FE2 ########
ip routing
ip multicast-routing vrf Engineering
ip pim vrf Engineering rp-address 200.2.3.100
ip pim vrf Engineering register-source Loopback500
!
interface Loopback0
description Fabric Node Router ID
ip address 70.0.0.2 255.255.255.255
ip router isis
!
vrf definition Engineering
rd 1:4099
!
address-family ipv4
route-target export 1:4099
route-target import 1:4099
exit-address-family
!
interface Vlan1021
mac-address 0000.5000.5000 < ---- Anycast MAc for gateway
vrf forwarding Engineering
ip address 100.1.1.1 255.255.255.0 <---- Anycast Gateway IP
ip pim sparse-dense-mode
no lisp mobility liveness test
lisp mobility v4eid
!
interface Loopback500
vrf forwarding Engineering
ip address 153.3.3.4 255.255.255.255
ip pim sparse-mode
end
!
router lisp
locator-set rloc_set1
IPv4-interface Loopback0 priority 10 weight 10
auto-discover-rlocs
exit-locator-set
!
service ipv4
encapsulation vxlan
map-cache-limit 5119
database-mapping limit dynamic 3000
itr map-resolver 71.0.0.1
etr map-server 71.0.0.1 key key1
etr map-server 71.0.0.1 proxy-reply
etr
sgt
proxy-itr 70.0.0.2
use-petr 71.0.0.1
exit-service-ipv4
!
instance-id 4097
remote-rloc-probe on-route-change
service ipv4
eid-table default
exit-service-ipv4
!
exit-instance-id
!
instance-id 4099
remote-rloc-probe on-route-change
dynamic-eid v4eid
database-mapping 100.1.0.0/16 locator-set rloc_set1
exit-dynamic-eid
service ipv4
eid-table vrf Engineering
database-mapping 153.3.3.4/32 locator-set rloc_set1 < — To register the address used by PIM source to the LISP MS/MR
map-cache 0.0.0.0/0 map-request
exit-service-ipv4
!
exit-instance-id
!
ipv4 locator reachability exclude-default
ipv4 source-locator Loopback0
exit-router-lisp
!
interface LISP0.4099
ip pim sparse-mode
!
##### FB1 ########
ip routing
ip multicast-routing vrf Engineering
ip pim vrf Engineering rp-address 200.2.3.100
ip pim vrf Engineering register-source Loopback500
!
interface Loopback0
description Fabric Node Router ID
ip address 71.0.0.1 255.255.255.255
ip router isis
!
vrf definition Engineering
rd 1:4099
!
address-family ipv4
route-target export 1:4099
route-target import 1:4099
exit-address-family
!
address-family ipv6
route-target export 1:4099
route-target import 1:4099
exit-address-family
!
interface Loopback1021 ----- ( Anycast gateway IP configured for DHCP OFFER punt)
vrf forwarding Engineering
ip address 100.1.1.1 255.255.255.255
!
interface Loopback500
vrf forwarding Engineering
ip address 200.2.3.100 255.255.255.255
ip pim sparse-mode
end
!
interface Vlan 2001
vrf forwarding Engineering
ip address 200.0.0.1 255.255.255.0
ip pim sparse-mode
end
!
router lisp
locator-set rloc_set1
IPv4-interface Loopback0 priority 10 weight 10
auto-discover-rlocs
exit-locator-set
!
service ipv4
encapsulation vxlan
map-cache-limit 5119
database-mapping limit dynamic 3000
itr map-resolver 71.0.0.1
etr map-server 71.0.0.1 key key1
etr map-server 71.0.0.1 proxy-reply
etr
sgt
proxy-etr
proxy-itr 71.0.0.1
map-server
map-resolver
exit-service-ipv4
!
instance-id 4097
remote-rloc-probe on-route-change
service ipv4
eid-table default
route-export site-registrations
distance site-registrations 250
map-cache site-registration
exit-service-ipv4
!
exit-instance-id
!
instance-id 4098
remote-rloc-probe on-route-change
service ipv4
eid-table vrf DEFAULT_VN
route-export site-registrations
distance site-registrations 250
map-cache site-registration
exit-service-ipv4
!
exit-instance-id
!
instance-id 4099
remote-rloc-probe on-route-change
service ipv4
eid-table vrf Engineering
database-mapping 200.2.3.100/32 locator-set rloc_set1 < — To register the RP address to the LISP MS/MR
route-import database bgp 65001 route-map database locator-set rloc_set1 ( — Replacement of redistribute bgp under router ospf)
route-export site-registrations
distance site-registrations 250
map-cache site-registration
exit-service-ipv4
!
exit-instance-id
!
!
site site_uci
authentication-key key1
eid-record instance-id 4097 0.0.0.0/0 accept-more-specifics
eid-record instance-id 4098 0.0.0.0/0 accept-more-specifics
eid-record instance-id 4099 0.0.0.0/0 accept-more-specifics
exit-site
!
!
ipv4 locator reachability exclude-default
ipv4 source-locator Loopback0
exit-router-lisp
!
interface LISP0.4099
ip pim sparse-mode
!
router bgp 65001
bgp router-id interface Loopback0
bgp log-neighbor-changes
bgp graceful-restart
!
address-family ipv4 vrf vn1
network 173.168.127.1 mask 255.255.255.255
network 200.2.3.100 mask 255.255.255.255 < ---- To advertise the RP address to upstream routers
aggregate-address 173.168.227.0 255.255.255.0 summary-only
aggregate-address 173.168.127.0 255.255.255.0 summary-only
neighbor 200.0.0.2 remote-as 65002
neighbor 200.0.0.2 activate
exit-address-family
!
route-map database permit 10
match ip address prefix-list external_prefix
!
ip prefix-list external_prefix seq 5 permit 200.0.0.0/8
Solution
Run the commands in the Post-SDA Troubleshooting to verify your device configuration. Fix errors, if any.
Pre-SDA Troubleshooting
show ip mroute vrf <vrf_name>
show ip mfib vrf <vrf_name>
Post-SDA Troubleshooting
- Check if the PIM tunnel is up.
===== FE1 ======
FE1#show ip pim vrf Engineering tunnel
Tunnel3
Type : PIM Encap
RP : 200.2.3.100
Source : 153.3.3.3
State : UP
Last event : Created (00:07:29) - Ensure IGMP joins are received on the Fabric node connected to the Multicast receiver.
FE1#show ip igmp vrf Engineering groups 226.1.1.1 detail
Flags: L - Local, U - User, SG - Static Group, VG - Virtual Group,
SS - Static Source, VS - Virtual Source,
Ac - Group accounted towards access control limit
Interface: Vlan1021
Group: 226.1.1.1
Flags: L U
Uptime: 00:01:50
Group mode: EXCLUDE (Expires: 00:02:27)
Last reporter: 100.1.1.10
Source list is empty - Verify if RPF check passes for RP address.
FE1#show ip rpf vrf Engineering 200.2.3.100
RPF information for ? (200.2.3.100)
RPF interface: LISP0.4099
RPF neighbor: ? (71.0.0.1)
RPF route/mask: 200.2.3.100/32
RPF type: unicast ()
Doing distance-preferred lookups across tables
RPF topology: ipv4 multicast base - Verify the output on receipt of joins from receiver and before sending traffic from source.
FE1#show ip mroute vrf Engineering 226.1.1.1
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:01:34/00:02:58, RP 200.2.3.100, flags: SJCL
Incoming interface: LISP0.4099, RPF nbr 71.0.0.1 < — RLOC of FB1
Outgoing interface list:
Vlan1021, Forward/Sparse-Dense, 00:01:34/00:02:58 - Verify S, G entry after starting traffic from the source.
FE1#show ip mroute vrf Engineering 226.1.1.1 < —
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:21:37/stopped, RP 200.2.3.100, flags: SJCL
Incoming interface: LISP0.4099, RPF nbr 71.0.0.1
Outgoing interface list:
Vlan1021, Forward/Sparse-Dense, 00:21:37/00:02:15
(200.5.6.100, 226.1.1.1), 00:02:12/00:00:47, flags: JT <---- S,G entry after traffic sent from source
Incoming interface: LISP0.4099, RPF nbr 71.0.0.1
Outgoing interface list:
Vlan1021, Forward/Sparse-Dense, 00:02:12/00:02:15 - Verify traffic hitting the mfib entry.
FE1#show ip mfib vrf Engineering 226.1.1.1
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: FS Pkt Count/PS Pkt Count
VRF Engineering
(*,226.1.1.1) Flags: C HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 625/0/104/0, Other: 0/0/0
LISP0.4099 Flags: A NS
Vlan1021 Flags: F IC NS
Pkts: 0/0
(200.5.6.100,226.1.1.1) Flags: HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 2523851/9899/104/8043, Other: 0/0/0 <---- Verify counters incrementing for S,G entry
LISP0.4099 Flags: A
Vlan1021 Flags: F IC NS
Pkts: 0/0 - Repeat steps on FE2.
==== FE2 ====
FE2#show ip pim vrf Engineering tunnel
Tunnel3
Type : PIM Encap
RP : 200.2.3.100
Source : 153.3.3.4
State : UP
Last event : Created (00:07:29)
FE2#show ip igmp vrf Engineering groups 226.1.1.1 detail
Flags: L - Local, U - User, SG - Static Group, VG - Virtual Group,
SS - Static Source, VS - Virtual Source,
Ac - Group accounted towards access control limit
Interface: Vlan1021
Group: 226.1.1.1
Flags: L U
Uptime: 00:01:50
Group mode: EXCLUDE (Expires: 00:02:27)
Last reporter: 100.1.1.11
Source list is empty
FE2#show ip rpf vrf Engineering 200.2.3.100
RPF information for ? (200.2.3.100)
RPF interface: LISP0.4099
RPF neighbor: ? (71.0.0.1)
RPF route/mask: 200.2.3.100/32
RPF type: unicast ()
Doing distance-preferred lookups across tables
RPF topology: ipv4 multicast base
FE2#show ip mroute vrf Engineering 226.1.1.1 <--- Output on Sending joins from receiver and before sending traffic from source)
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:01:34/00:02:58, RP 200.2.3.100, flags: SJCL
Incoming interface: LISP0.4099, RPF nbr 71.0.0.1
Outgoing interface list:
Vlan1500, Forward/Sparse-Dense, 00:01:34/00:02:58
FE2#show ip mroute vrf Engineering 226.1.1.1 < — Verify S,G entry after starting traffic from source
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:21:37/stopped, RP 200.2.3.100, flags: SJCL
Incoming interface: LISP0.4099, RPF nbr 71.0.0.1
Outgoing interface list:
Vlan1021, Forward/Sparse-Dense, 00:21:37/00:02:15
(200.5.6.100, 226.1.1.1), 00:02:12/00:00:47, flags: JT <---- S,G entry after traffic sent from source
Incoming interface: LISP0.4099, RPF nbr 71.0.0.1
Outgoing interface list:
Vlan1021, Forward/Sparse-Dense, 00:02:12/00:02:15
FE2#show ip mfib vrf Engineering 226.1.1.1
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: FS Pkt Count/PS Pkt Count
VRF vrf5000
(*,226.1.1.1) Flags: C HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 625/0/104/0, Other: 0/0/0
LISP0.4099 Flags: A NS
Vlan1021 Flags: F IC NS
Pkts: 0/0
(200.5.6.100,226.1.1.1) Flags: HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 2523851/9899/104/8043, Other: 0/0/0 <---- Verify counters incrementing for S,G entry
LISP0.4099 Flags: A
Vlan1021 Flags: F IC NS
Pkts: 0/0 - Repeat steps on Fabric Border (FB)
==== FB1 ====
FB1#show ip pim vrf Engineering tunnel
Tunnel5
Type : PIM Encap
RP : 200.2.3.100*
Source : 200.2.3.100
State : UP
Last event : Created (02:39:37)
Tunnel7*
Type : PIM Decap
RP : 200.2.3.100*
Source : -
State : UP
Last event : Created (02:39:37)
FBR#show ip mroute vrf Engineering 226.1.1.1 <--- Output on Sending joins from receiver and before sending traffic from source)
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:04:39/00:03:03, RP 200.2.3.100, flags: S
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4099, 70.0.0.1, Forward/Sparse, 00:04:39/00:03:03 < ---- 2 entries as there are 2 receivers behind 2 FEs
LISP0.4099, 70.0.0.2, Forward/Sparse, 00:04:39/00:03:03 <-----
SG-FBR1#show ip mroute vrf vrf5000 226.1.1.1 <---- Verify S,G entry after starting traffic from source
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry, E - Extranet,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group,
G - Received BGP C-Mroute, g - Sent BGP C-Mroute,
N - Received BGP Shared-Tree Prune, n - BGP C-Mroute suppressed,
Q - Received BGP S-A Route, q - Sent BGP S-A Route,
V - RD & Vector, v - Vector, p - PIM Joins on route,
x - VxLAN group, c - PFP-SA cache created entry,
* - determined by Assert
Outgoing interface flags: H - Hardware switched, A - Assert winner, p - PIM Join
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 226.1.1.1), 00:26:17/00:03:02, RP 200.2.3.100, flags: S
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
LISP0.4099, 70.0.0.1, Forward/Sparse, 00:26:17/00:03:02
LISP0.4099, 70.0.0.2, Forward/Sparse, 00:26:17/00:03:02
(200.5.6.100, 226.1.1.1), 00:06:03/00:01:55, flags: T
Incoming interface: Vlan2001, RPF nbr 200.0.0.2
Outgoing interface list:
LISP0.4099, 70.0.0.1, Forward/Sparse, 00:06:03/00:03:02
LISP0.4099, 70.0.0.2, Forward/Sparse, 00:06:03/00:03:02
FB1#show ip mfib vrf Engineering 226.1.1.1
Entry Flags: C - Directly Connected, S - Signal, IA - Inherit A flag,
ET - Data Rate Exceeds Threshold, K - Keepalive
DDE - Data Driven Event, HW - Hardware Installed
ME - MoFRR ECMP entry, MNE - MoFRR Non-ECMP entry, MP - MFIB
MoFRR Primary, RP - MRIB MoFRR Primary, P - MoFRR Primary
MS - MoFRR Entry in Sync, MC - MoFRR entry in MoFRR Client.
I/O Item Flags: IC - Internal Copy, NP - Not platform switched,
NS - Negate Signalling, SP - Signal Present,
A - Accept, F - Forward, RA - MRIB Accept, RF - MRIB Forward,
MA - MFIB Accept, A2 - Accept backup,
RA2 - MRIB Accept backup, MA2 - MFIB Accept backup
Forwarding Counts: Pkt Count/Pkts per second/Avg Pkt Size/Kbits per second
Other counts: Total/RPF failed/Other drops
I/O Item Counts: FS Pkt Count/PS Pkt Count
VRF Engineering
(*,226.1.1.1) Flags: C HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 3/0/84/0, Other: 0/0/0
Tunnel7 Flags: A
LISP0.4099, 70.0.0.1 Flags: F NS
Pkts: 0/0
(200.5.6.100,226.1.1.1) Flags: HW
SW Forwarding: 0/0/0/0, Other: 0/0/0
HW Forwarding: 8428458/10000/99/7812, Other: 0/0/0
Vlan2001 Flags: A
LISP0.4099, 70.0.0.1Flags: F NS
Pkts: 0/0
LISP0.4099, 70.0.0.2Flags: F NS
Pkts: 0/0
