PROJ

[NaoyaKun]

 WHY I CAN'T CONNECT MY WLAN TO THE SERVER ? LIKE IT ALWAYS SHOW SERVER REQ TIMEOUT? CAN YOU HELP ME?

[liviu.gheorghe]

Hello @NaoyaKun ,

can you provide more information and details about your wlan configuration in order to try to understand what the problem is?

[NaoyaKun]

like i already create a vlan and used trunk here some picture of my project

[liviu.gheorghe]

Can you share the Packet Tracer file?

[NaoyaKun]

i can insert now btw 

[liviu.gheorghe]

Your configs are not ok. 

I looked at the configs for FLR2-SW1 and FLR2-SW1 and the requirement is to configure 4 ports in an etherchannel (Fa0/1 - Fa0/4). I saw that all the ports where configured as members of Port-channel 1. My firs recommendation is to remove the port-channel 1 mode on from interfaces Fa0/5 - Fa0/24, Gi0/1 and Gi0/2 from both switches FLR2-SW1 and FLR2-SW1.

The same recommendation is for FLR1-SW1 - remove port-channel 1 mode on from all switch interfaces.

Can you tell me exactly what you where trying to test and didn't work?

[NaoyaKun]

i cant log in on Mgmt-PC using wlan. like it always server request timeout.

[liviu.gheorghe]

There are a few things that are missing:

1. On the CORE-SW:

enable ip routing with the ip routing command

configure the 2 static routes to the users VLAN's

ip route 10.10.0.0 255.255.0.0 GigabitEthernet1/0/23

ip route 10.10.0.0 255.255.0.0 GigabitEthernet1/0/24 200

2. On the GTWY1

IP on Gi0/0/0 is wrong - it should be 192.168.3.254/24

in dhcp pool V20 add the command: option 43 ip 192.168.1.254

the static default route was not correct - it should be  ip route 0.0.0.0 0.0.0.0 192.168.3.1

3. On GTWY2

the dhcp pool V20 is missing - it should be created exactly like the one on GTWY1

4. In order to configure the WLC with the requirements from point 4.) you will need to access the WLC on https://192.168.1.254 from MGMT-PC1. For this to work, you should configure interface Fa0/7 on FLR2-SW1 as follows:

interface FastEthernet0/7

no switchport nonegotiate

no switchport mode trunk

no switchport trunk native vlan 20

switchport access vlan 20

After this configuration of Fa0/7 you will be able to access the WLC on  https://192.168.1.254 and configure the 4.) requirements. By the way, the username/password to access the WLC is admin/admin not the one from the requirements (admin/Pa$$word).

[NaoyaKun]

it still request timie the WLC-MgmtPC? what other things can i do? and im using wireless like the WMP300N

[liviu.gheorghe]

Have you accessed the WLC (https://192.168.1.254) from the MGMT-PC and implemented the tasks listed at number 4. Implementing mobility service using WLAN in the script:

 i.      Create interface groups named “EmployeeWiFi” and “GuestWiFi” for VLAN 10 and VLAN 50 respectively. Use Port number 1 and 9^th useable IP address of the VLAN for physical information and interface address respectively.

 ii.      Create WLAN profiles for VLAN 10 and VLAN 50, and consider as follows:

1.       Profile name of “Employee WiFi” with ID of 2 and “Guest WiFi” with ID of 3.
2.       SSID of “EmployeeWiFi” and “GuestWiFi”.

iii.      Use WPA2 Personal security for with PSK’s “”0123456789” and “9876543210” for “EmployeeWiFi” and “GuestWiFi” respectively.

iv.      Enable FlexConnect Local Switching and FlexConnect Local Auth

The WLC has a graphical interface in which you configure tasks i-iv and after the configuration, the EmployeeWpc1 and GuestWpc1 will be able to connect to the EmployeeWiFi and GuestWiFi SSID respectively.

[NaoyaKun]

i do configure the floor 2 s1 but the on mgmt pc web browser was always time out and i cant still connect my wmp300n.

[liviu.gheorghe]

I think you skipped task 2.c - In CORE-SW, create additional VLAN 2 as the PrivateSRV's network with default name . Configure SVI's VLAN 1 and VLAN 2) and routed-ports (Gig1/0/22-24) with appropriate IP addresses described in the addressing table above..

You should have the following config in CORE-SW:

interface GigabitEthernet1/0/1

switchport access vlan 2

interface Vlan2

mac-address 00e0.8f3d.8901

ip address 192.168.2.1 255.255.255.0

You should be able to reach now the WLC from MGMT-PC1

[NaoyaKun]

i was talking the WLC-MgmtPC not the MgmtPC-1. like on the no.4 i have to go on 192.168.1.254 but the server say request timeout.

[liviu.gheorghe · Accepted solution]

Yes, I know your assignment says to access the WLV from WLV-MgmtPC, but without the password for SSID MgmtWiFi - which is the only one configured on the WLC at this moment - you cannot connect to this network and you cannot access the WLC.

I was offering an alternative to access the WLC from the MGMT-PC1 and complete task 4.

[NaoyaKun]

i tried on mgmt-pc but req time. So i connect the wls-mgmtpc to core-sw but it has also a req timeout btw the mac-address 00e0.8f3d.8901 wont work