10-14-2013 04:03 AM
Hi,
I was wondering that I'm not able to get transceiver details on a c6500 (with sup720-bxl) platform running version 15.1(1)SY1.
Xenpaks will do fine:
c6504#sh int Te3/3 transceiver
ITU Channel not available (Wavelength not available),
Transceiver is internally calibrated.
Alarms applicable when thresholds or values are not N/A.
If device is externally calibrated, only calibrated values are printed.
++ : high alarm, + : high warning, - : low warning, -- : low alarm.
NA or N/A: not applicable, Tx: transmit, Rx: receive.
mA: milliamperes, dBm: decibels (milliwatts).
Optical Optical
Temperature Voltage Current Tx Power Rx Power
Port (Celsius) (Volts) (mA) (dBm) (dBm)
---------- ----------- ------- -------- -------- --------
Te3/3 30.1 N/A 30.4 -- -0.9 -2.0
While a SFP-GE-L fails:
c6504#sh int Gi4/23 transceiverDiagnostic Monitoring is not implemented.
The SFP has definitivly DOM/DDM support enabled. If I plugg the optic in a C2960G switch, I can query the transceiver details-
c6504#sh int transceiver supported-modules
Mod DOM support
---- --------------
1 Applicable
3 Applicable
4 Applicable
c6504#sh int transceiver supported-list
Transceiver Types depends on Supervisor/Line card
Transceiver Type Cisco p/n min version
supporting DOM
------------------ -------------------------
DWDM GBIC ALL
DWDM SFP ALL
RX only WDM GBIC ALL
DWDM XENPAK ALL
DWDM X2 ALL
DWDM XFP ALL
CWDM GBIC NONE
CWDM X2 ALL
CWDM XFP ALL
XENPAK ZR ALL
X2 ZR ALL
XFP ZR ALL
RX only WDM XENPAK ALL
XENPAK ER 10-1888-04
X2 ER ALL
XFP ER ALL
XENPAK LR 10-1838-04
X2 LR ALL
XFP LR ALL
XENPAK LW ALL
X2 LW ALL
XFP LW NONE
XENPAK SR NONE
X2 SR ALL
XFP SR ALL
XENPAK LX4 NONE
X2 LX4 NONE
XFP LX4 NONE
SX GBIC NONE
LX GBIC NONE
ZX GBIC NONE
CWDM SFP ALL
RX only WDM SFP NONE
1000BaseSX SFP ALL
1000BaseLX SFP ALL
1000BaseZX SFP ALL
100BaseSX SFP NONE
100BaseLX SFP NONE
100BaseZX SFP NONE
GigE BX U SFP ALL
GigE BX D SFP ALL
SFP+ SR ALL
SFP+ LR ALL
SFP+ LRM ALL
SFP+ ER ALL
X2 LRM ALL
CFP SR4 ALL
CFP LR4 ALL
Any hints?
Thanks,
Thomas
Solved! Go to Solution.
10-20-2013 08:41 PM
Most linecards on the 6500 do not support DOM even though the transceivers are capable.
Please refer to the matrix in the following document, beginning on page 47:
Please rate helpful posts.
10-20-2013 08:41 PM
Most linecards on the 6500 do not support DOM even though the transceivers are capable.
Please refer to the matrix in the following document, beginning on page 47:
Please rate helpful posts.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide