11-14-2005 08:36 AM - last edited on 03-25-2019 06:49 PM by ciscomoderator
Hello,
I have configured a 2821 with 1 - E1 and 2 - BRI interfaces.
The protocol used for the E1 is Qsig, the is a connection to a siemens Hipath 4000. This connection is working fine in normal mode.
When the Gateway is working in SRST mode I can receive call from the siemens I cannot make calls. In the debuging I see that I try to establish the call but after that the call is interrupted.
Does someone have more information about a Qsig link to a siemens with SRST
Kind regards
11-14-2005 03:38 PM
Hi,
Found these links, you may paste your debugs and config so we can take a look.
11-16-2005 05:13 AM
Hello
Thanks for your reply
Here do you have the output for the call under srst
*Nov 16 12:06:19.863: ISDN Se0/1/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=3 n
r=3
*Nov 16 12:06:19.867: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0002
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA9839F
Exclusive, Channel 31
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0080, '1076'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '027271212'
Plan:Unknown, Type:Unknown
*Nov 16 12:06:19.887: ISDN Se0/1/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=4
*Nov 16 12:06:19.915: ISDN Se0/1/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=3 n
r=4
*Nov 16 12:06:19.915: ISDN Se0/1/0:15 Q931: CALL_PROC pd = 8 callref = 0x8002
Channel ID i = 0xA1839F
Preferred, Channel 31
Here do you have the output during normal CCM
*Nov 16 12:16:02.191: ISDN Se0/1/0:15 Q921: User TX -> INFO sapi=0 tei=0, ns=0 n
r=0
*Nov 16 12:16:02.191: ISDN Se0/1/0:15 Q931: SETUP pd = 8 callref = 0x0001
Sending Complete
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA98381
Exclusive, Channel 1
Calling Party Number i = 0x0081, '1076'
Plan:Unknown, Type:Unknown
Called Party Number i = 0x80, '0027271212'
Plan:Unknown, Type:Unknown
*Nov 16 12:16:02.211: ISDN Se0/1/0:15 Q921: User RX <- RR sapi=0 tei=0 nr=1
*Nov 16 12:16:02.243: ISDN Se0/1/0:15 Q921: User RX <- INFO sapi=0 tei=0, ns=0 n
r=1
*Nov 16 12:16:02.243: ISDN Se0/1/0:15 Q931: CALL_PROC pd = 8 callref = 0x8001
Channel ID i = 0xA98381
Exclusive, Channel 1
So during SRST he is using channel 31 ? and I'm getting the message originating address is non-isdn
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide