06-28-2004 11:27 PM - edited 03-02-2019 04:42 PM
hi,
we have a 3640 router with 4 slots free. i have an NM 1E2W module inserted in one of the slots and in that NM 1E 2W i have inserted a WIC2T wan card. problem is that it is recoginising the NM Module while boot up but not the wic2t. i am not able to see any serial interfaces on the running configuration file. but when i give " sh diag " - i am able to see the father card as NM1E2w and daughter card as Wic2t.
ios version is 12.2(24)T.
i have tried putting another wic2t in that , but still i am facing the same problem.
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-I-M), Version 12.2(24a), RELEASE SOFTWARE
(fc3)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Fri 28-May-04 18:05 by pwade
Image text-base: 0x60008930, data-base: 0x60A3C000
ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE
(fc1)
Router uptime is 15 minutes
System returned to ROM by reload
System image file is "flash:c3640-i-mz.122-24a.bin"
cisco 3640 (R4700) processor (revision 0x00) with 126976K/4096K bytes of
memory.
Processor board ID 11247200
R4700 CPU at 100Mhz, Implementation 33, Rev 1.0
Bridging software.
X.25 software, Version 3.0.0.
1 Ethernet/IEEE 802.3 interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (Read/Write)
Configuration register is 0x2102
-----------------------------------------------------
------------------ show diag ------------------
Slot 0:
Combo 1E, 2W Port adapter, 3 ports
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 1.2 Board revision F0
Serial number 29384181 Part number 800-01789-05
FRU Part Number: NM-1E2W=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 37 01 02 01 C0 5D F5 50 06 FD 05 00 00 00 00
0x30: 78 00 00 00 02 10 08 17 FF FF FF FF FF FF FF FF
WIC Slot 0:
Serial 2T (12in1) WAN daughter card
Hardware revision 1.0 Board revision H0
Serial number 29643622 Part number 800-03181-01
Test history 0x0 RMA number 00-00-00
Connector type PCI
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 12 01 00 01 C4 53 66 50 0C 6D 01 00 00 00 00
0x30: 88 FD 81 00 02 12 25 00 FF FF FF FF FF FF FF FF
-----------------------------------------------------
can any one help me
06-29-2004 05:01 AM
The WIC-2T is not supported in a NM-1E-2W module on the 3640 platform.
http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a00800b0858.shtml#plat
Quote "The NM-1E2W, NM-1E1R2W, and NM-2E2W Network Modules do not have enough performance power to support the WIC-2T due to hardware limitations."
07-05-2004 11:20 PM
thank you, it solved my problem
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide