Can WS-X6066-SLB-APC be used with WS-X6K-SUP1A-2GE?

[jackgaoyang]

A 6509 Chasis with 6066 in Slot 4 but cannot work:

Console> (enable) 2005 Mar 21 21:39:56 %SYS-5-MOD_NOTSUPPORTED:Module 4 is not supported

Console> (enable) show module

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAD05050MW2

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-01-c9-6d-75-36 to 00-01-c9-6d-75-37 7.0 5.3(1) 6.4(4a)

00-01-c9-6d-75-34 to 00-01-c9-6d-75-35

00-d0-05-29-84-00 to 00-d0-05-29-87-ff

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- ----------------------- ------------------- ----------- ------

1 L2 Switching Engine II WS-F6020A SAD05050DS6 2.0

Console> (enable) show module

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAD05050MW2

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-01-c9-6d-75-36 to 00-01-c9-6d-75-37 7.0 5.3(1) 6.4(4a)

00-01-c9-6d-75-34 to 00-01-c9-6d-75-35

00-d0-05-29-84-00 to 00-d0-05-29-87-ff

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw

--- ----------------------- ------------------- ----------- ------

1 L2 Switching Engine II WS-F6020A SAD05050DS6 2.0

[alagrawa]

Hi Jack,

Hope you're doing well. On the cat6500 switch, the CSM module needs minimum CatOS code 7.5(1). The recommended code is 7.6(9). This is mentioned in the release notes at the link below.

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/ol_4498.htm#wp419671

Please note that by default the sup1A ships with 64MB DRAM. To upgrade to codes 7.5(1) and above, it is recommended to have minimum 128MB DRAM. Hence, it will be advisable to upgrade the DRAM before you upgrade the code.

Also, I found the following link.

http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/relnotes/ol_6897.htm#wp16934

This link mentions that you must have a sup1A with a MSFC. From your show module, it looks like you dont have the MSFC daughter card. Hence, you wont be able to support the CSM module with this superviro module.

Hope that helps.

regards

-Alok

[jackgaoyang]

Now I have a sup2, but the csm still not work, is this a hardware problem?

Console> (enable) reset 9

This command will reset module 9.

Do you want to continue (y/n) [n]? y

2005 Mar 25 03:57:17 %SYS-5-MOD_RESET:Module 9 reset from Console//

Resetting module 9...

Console> (enable) Sending RARP request with address 00:d0:05:29:87:ff

Sending DHCP packet with address: 00:d0:05:29:87:ff

LCP Error: EOBC Loopback Test Failed Device: 0

Module 9 failure due to EOBC Loopback Test Failed

2005 Mar 25 03:58:23 %SYS-3-MOD_FAILREASON:Module 9 failed due to EOBC Loopback Test Failed

Console> (enable) show module

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP2-2GE yes ok

15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok

9 9 4 Content Switching Module WS-X6066-SLB-APC no other

Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAL081553P9

15 SAL08290FUG

9 SAD0743003S

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-06-d6-5e-c9-6a to 00-06-d6-5e-c9-6b 5.1 7.1(1) 8.1(3)

00-06-d6-5e-c9-68 to 00-06-d6-5e-c9-69

00-d0-05-29-84-00 to 00-d0-05-29-87-ff

15 00-09-12-6d-f5-80 to 00-09-12-6d-f5-bf 2.8 12.1(13)E1 12.1(13)E15

9 00-0d-bc-af-b9-30 to 00-0d-bc-af-b9-37 1.7 0.0

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw

--- ----------------------- ------------------- ----------- ------ ------

1 L3 Switching Engine II WS-F6K-PFC2 SAL08373PUL 3.5

Console> (enable)

[alagrawa]

This does look like hardware failure.It might be a good idea to test it on another slot if you have a spare slot.

regards

-Alok

[jackgaoyang]

I've changed several slots, it's the same

Thank you for your help