Cisco 1700 boot problem

vikrantarora · ‎09-30-2003

I uploaded the image in the Cisco 1700 from c1700-y-mz.122-4.YA2.bin to c1700-y-mz.122-4.YA6.bin.

But I started getting the error "Serial0/0 is up, line protocol is down" on the router 2600 which has a serial link to the 1700 on which we did the upgrade.

1700 was in a remote location, so we brought it in our office and it came up in "rommon" mode. I erased the flsh, brought in c1700-y-mz.122-4.YA6.bin via tftp.

I have the following 2 questions:

1. How do I check what versions of IOs are compatible wiht my WAN card.

2. How do I make the router take this configuration on startup as everytime I reset the router, it comesup in rommon mode adn I have to mannually boot it form the configuration file.

The following outputs (sh diag nad sh ver) might be helpful:

Router#sh diag

Slot 0:

C1721 1FE Mainboard Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

Hardware Revision : 1.0

PCB Serial Number : FOC07240KBR

Part Number : 73-7546-01

Board Revision : A0

Fab Version : 04

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 5A 41 01 00 C1 8B 46 4F 43 30 37 32

0x10: 34 30 4B 42 52 82 49 1D 7A 01 42 41 30 02 04 FF

0x20: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x30: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x40: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

WIC Slot 0:

FT1

Hardware revision 1.5 Board revision G0

Serial number 0030520391 Part number 800-03279-04

Test history 0x00 RMA number 00-00-00

Connector type WAN Module

EEPROM format version 2

EEPROM contents (hex):

0x20: 02 11 01 05 01 D1 B4 47 50 0C CF 04 00 00 00 00

0x30: 80 00 00 00 03 05 07 01 FF FF FF FF FF FF FF FF

Router#sh ver

Cisco Internetwork Operating System Software

IOS (tm) C1700 Software (C1700-Y-M), Version 12.2(4)YA6, EARLY DEPLOYMENT RELEAS

E SOFTWARE (fc1)

Synched to technology version 12.2(5.4)T

TAC Support: http://www.cisco.com/tac

Compiled Wed 23-Jul-03 19:38 by ealyon

Image text-base: 0x80008124, data-base: 0x807983C0

ROM: System Bootstrap, Version 12.2(7r)XM1, RELEASE SOFTWARE (fc1)

ROM: C1700 Software (C1700-Y-M), Version 12.2(4)YA6, EARLY DEPLOYMENT RELEASE SO

FTWARE (fc1)

Router uptime is 6 minutes

System returned to ROM by power-on

System image file is "flash:c1700-y-mz.122-4.YA6.bin"

cisco 1721 (MPC860P) processor (revision 0x100) with 29492K/3276K bytes of memor

y.

Processor board ID FOC07240KBR (2841942417), with hardware revision 0000

MPC860P processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

1 FastEthernet/IEEE 802.3 interface(s)

1 Serial network interface(s)

WIC T1-DSU

32K bytes of non-volatile configuration memory.

16384K bytes of processor board System flash (Read/Write)

Configuration register is 0x8002

deilert · ‎09-30-2003

your config register is set to the wrong values , try this

router#conf t

router#(conf)config-register 0x2102

router# reload

vikrantarora · ‎09-30-2003

Before I got yoor reply, I changed it to 0x8002 and now it is working fine. I dont understand what's going on. Should one set the value of the confgiuration register to the value appearing in the last line of the 'sh ver' command or should it

always be 0x2102.

Can I go ahead and configure the router. Please see output of current sh ver below:

Router#sh ve

00:03:43: %SYS-5-CONFIG_I: Configured from console by consoler