07-31-2004 12:10 AM - edited 03-02-2019 05:26 PM
Dear friends,
i have a cisco router 2509 and i attached 8 modems external US ROBOTICS 56K faxmodem, but after configured them i get just 33600 or 31200 on connections from dialin.
this is my configuration and i just put modem cap usr_sportster because i don't know how to insert the modemcap for these modems us robotics 56k
some one can help me to setup these modems to connect at 56000 bps????
Thanks and regards
my e-mail is : romolo67@hotmail.com
Using 2548 out of 32762 bytes
!
version 11.2
!
hostname elgounaspeed
!
enable secret xxxx
enable password xxxx
!
username pippo password xxxx
ip subnet-zero
!
interface Loopback0
ip address 10.10.11.5 255.255.255.0
ip broadcast-address 0.0.0.0
!
interface Ethernet0
ip address 192.168.0.1 255.255.255.0
ip broadcast-address 0.0.0.0
!
interface Serial0
no ip address
no ip mroute-cache
no ip route-cache
shutdown
!
interface Serial1
no ip address
shutdown
!
interface Async1
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.10
no cdp enable
ppp authentication pap
!
interface Async2
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.11
no cdp enable
ppp authentication pap
!
interface Async3
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.12
no cdp enable
ppp authentication pap
!
interface Async4
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.13
no cdp enable
ppp authentication pap
!
interface Async5
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.14
no cdp enable
ppp authentication pap
!
interface Async6
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.15
no cdp enable
ppp authentication pap
!
interface Async7
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.16
no cdp enable
ppp authentication pap
!
interface Async8
ip unnumbered Ethernet0
encapsulation ppp
async dynamic address
async mode interactive
peer default ip address 192.168.0.17
no cdp enable
ppp authentication pap
!
router igrp 15
network 192.168.0.0
!
ip local pool setup_pool 192.168.0.10 192.168.0.17
ip classless
ip route 0.0.0.0 0.0.0.0 10.21.5.110
ip route 10.21.5.0 255.255.255.0 10.21.5.110
no logging console
dialer-list 1 protocol ip permit
dialer-list 1 protocol ipx permit
!
line con 0
exec-timeout 0 0
line 1 8
autoselect arap
autoselect during-login
autoselect ppp
login local
modem InOut
modem autoconfigure type usr_sportster
transport input all
stopbits 1
rxspeed 115200
txspeed 115200
flowcontrol hardware
line aux 0
line vty 0 4
password xxx
login
!
end
elgounaspeed#sh modemcap usr_sportster
Modemcap values for usr_sportster
Factory Defaults (FD): &F
Autoanswer (AA): S0=1
Carrier detect (CD): &C1
Drop with DTR (DTR): &D2
Hardware Flowcontrol (HFL): &H1&R2
Lock DTE speed (SPD): &B1
DTE locking speed (DTE): [not set]
Best Error Control (BER): &M4
Best Compression (BCP): &K1
No Error Control (NER): &M0
No Compression (NCP): &K0
No Echo (NEC): E0
No Result Codes (NRS): Q1
Software Flowcontrol (SFL): [not set]
Caller ID (CID): [not set]
On-hook (ONH): H0
Off-hook (OFH): H1
Miscellaneous (MSC): [not set]
Template entry (TPL): usr_courier
Modem entry is built-in.
08-02-2004 02:36 AM
Hello,
Below are two links that will be helpful in configuring and troubleshooting external modems.
http://www.cisco.com/warp/public/76/9.html
Try using the appropriate modem cap for your modem, for 56k connections.
fm
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: