11-08-2002 07:49 AM - edited 03-02-2019 02:45 AM
Hi
Has any one had problems with 803 cisco routers? On startup the layer1 of isdn is not activated eventhough isdn switch/cable is o.k.Once router is up and you takeout out the isdn cable and put it back in the Layer 1 comes up automatically.below is result of debug isdn q921
00:02:29: ISDN BR0: TX -> IDREQ ri=29609 ai=127
00:02:29: ISDN BR0: RX <- IDASSN ri=29609 ai=64
00:02:29: ISDN BR0: TX -> SABMEp c/r=0 sapi=0 tei=64
00:02:29: ISDN BR0: RX <- UAf c/r=0 sapi=0 tei=64
00:02:29: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 64 changed to up
00:02:30: ISDN BR0: TX -> INFOc sapi=0 tei=64 ns=0 nr=0 i=0x08010105040288901801
83700D80393032303833353835373132
00:02:30: ISDN BR0: RX <- RRr sapi=0 tei=64 nr=1
00:02:30: ISDN BR0: RX <- INFOc sapi=0 tei=64 ns=0 nr=1 i=0x0801810D180189
00:02:30: ISDN BR0: TX -> RRr sapi=0 tei=64 nr=1
00:02:30: ISDN BR0: RX <- INFOc sapi=0 tei=64 ns=1 nr=1 i=0x08018102180189
00:02:30: ISDN BR0: TX -> RRr sapi=0 tei=64 nr=2
00:02:32: ISDN BR0: RX <- INFOc sapi=0 tei=64 ns=2 nr=1 i=0x08018101281239303230
3833353835373132204C4F43414C
00:02:33: ISDN BR0: TX -> RRr sapi=0 tei=64 nr=3
00:02:33: ISDN BR0: RX <- INFOc sapi=0 tei=64 ns=3 nr=1 i=0x08018107281239303230
3833353835373132204C4F43414C2905020B0612064C0E0183393032303833353835373132
00:02:33: ISDN BR0: TX -> RRr sapi=0 tei=64 nr=4
00:02:141733920768: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
00:02:33: ISDN BR0: TX -> INFOc sapi=0 tei=64 ns=1 nr=4 i=0x0801010F
00:02:33: ISDN BR0: RX <- RRr sapi=0 tei=64 nr=2
00:02:34: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0:1, changed state
to up
00:02:39: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to 902083585712 NKB
H2
00:02:43: ISDN BR0: RX <- RRp sapi=0 tei=64 nr=2
00:02:43: ISDN BR0: TX -> RRf sapi=0 tei=64 nr=4
any input will be appreciated thanks
11-08-2002 09:32 AM
803 should detect layer 1 and 2 active, automatically..Pl. try to wait till 20-40 secs after the router fully boot up and then enter "sh isdn status"..
If that results the same, then pl. let us know the version of ios that you run..
11-11-2002 01:48 PM
I have seen this problem before in Australia. It can take between 5 to 10 minutes for layer one to become active. What it tends to be is that the NT1 that the Telco uses does tend to detect the end device. I have got them (Telco) in the past to hard set that layer one is always active and this fixes the problem.
Just a thought. Hope it helps
11-14-2002 01:44 AM
can u give me the show run of the router
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide