I'm trying to configure my soho97 router with adsl, but it doesn't works. I'm in the UK with a fixed IP address and using pppoa, chap, vc-mux and pvc 0/38.
from the internal lan I can ping int e0(10.10.10.1) and int d1(82.x.x.x) with no issues, but 1 cannot the isp’s dns server 212.23.8.1.
from the router console I can only ping 10.10.10.1 with success. int d1 and isp dns no good..
Sample below
Building configuration...
Current configuration : 1685 bytes
!
version 12.3
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname RouterSOHO97
!
ip subnet-zero
ip name-server 212.x.8.1
ip name-server 212.23.8.6
ip dhcp excluded-address 10.10.10.1
!
ip dhcp pool CLIENT
network 10.10.10.0 255.255.255.0
default-router 10.10.10.1
dns-server 212.x.x.x.23.8.6
lease 0 2
!
!
no aaa new-model
!
interface Ethernet0
ip address 10.10.x.x.255.255.0
ip nat inside
ip tcp adjust-mss 1452
hold-queue 100 out
!
interface ATM0
no ip address
atm vc-per-vp 128
no atm ilmi-keepalive
pvc 0/38
encapsulation aal5mux ppp dialer
!
dsl operating-mode auto
!
interface Dialer1
ip address 82.x.x.x 255.255.255.248
ip mtu 1492
ip nat outside
encapsulation ppp
ip tcp adjust-mss 1452
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxxxxx
ppp chap password xxxx
ppp pap sent-username xxxxxx password xxxx!
ip nat inside source list 102 interface Dialer1 overload
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
ip http server
no ip http secure-server
!
access-list 23 permit 10.10.10.0 0.0.0.255
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
dialer-list 1 protocol ip permit
!
line con 0
exec-timeout 120 0
no modem enable
stopbits 1
line aux 0
line vty 0 4
access-class 23 in
exec-timeout 120 0
login local
length 0
!
scheduler max-task-time 5000
!
End
Below some diags samples;
show int atm 0
ATM0 is up, line protocol is up
Hardware is PQUICC_SAR (with Alcatel ADSL Module)
MTU 1500 bytes, sub MTU 1500, BW 288 Kbit, DLY 80 usec,
reliability 68/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5 AAL2, PVC mode
10 maximum active VCs, 128 VCs per VP, 1 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
Last input never, output 00:14:02, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: Per VC Queueing
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
16 packets output, 1120 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 output buffer failures, 0 output buffers swapped out
RouterSOHO97#
sh atm int atm0
Interface ATM0:
AAL enabled: AAL5 AAL2, Maximum VCs: 10, Current VCCs: 1
Maximum Transmit Channels: 0
VCIs per VPI: 128,
Max. Datagram Size: 1528
PLIM Type: ADSL - 800Kbps Upstream, DMT, TX clocking: LINE
0 input, 16 output, 0 IN fast, 0 OUT fast
Avail bw = 800
Config. is ACTIVE
RouterSOHO97#
sh ip int bri
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM up up
Dialer1 82.x.x.x YES manual up up
Ethernet0 10.10.10.1 YES NVRAM up up
RouterSOHO97#
Sorry for the large amount of info. hopefully it will help solve my problems..
Thanx
:)
