05-17-2002 06:00 AM - edited 03-01-2019 09:46 PM
I'm trying to set up an ASYNC dialin access , with an analog modem , to a cisco 1003 isdn router.
The connection seems to complete successfully at L1 but the LCP seems not to work
here after an extract from the router's log
Mar 1 00:51:57: %ISDN-6-LAYER2UP: Layer 2 for Interface BR0, TEI 69 changed to up
*Mar 1 00:51:57: ISDN BR0: RX <- SETUP pd = 8 callref = 0x39
*Mar 1 00:51:57: Sending Complete
*Mar 1 00:51:57: Bearer Capability i = 0x9090A3
*Mar 1 00:51:57: Channel ID i = 0x89
*Mar 1 00:51:57: Progress Ind i = 0x8583 - Origination address is non-ISDN
*Mar 1 00:51:57: Calling Party Number i = '!', 0x83, '5141326'
*Mar 1 00:51:57: Called Party Number i = 0xA1, '516415463'
*Mar 1 00:51:57: %LINK-3-UPDOWN: Interface BRI0:1, changed state to up
*Mar 1 00:51:57: BR0:1 PPP: Treating connection as a callin
*Mar 1 00:51:57: BR0:1 PPP: Phase is ESTABLISHING, Passive Open
*Mar 1 00:51:57: BR0:1 LCP: State is Listen
*Mar 1 00:51:57: ISDN BR0: TX -> CONNECT pd = 8 callref = 0xB9
*Mar 1 00:51:57: ISDN BR0: RX <- CONNECT_ACK pd = 8 callref = 0x39
*Mar 1 00:52:00: BR0:1 LCP: TIMEout: Time 0x2FFD38 State Listen
*Mar 1 00:52:00: BR0:1 LCP: O CONFREQ [Listen] id 56 len 32
*Mar 1 00:52:00: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
*Mar 1 00:52:00: BR0:1 LCP: MagicNumber 0x607750A1 (0x0506607750A1)
*Mar 1 00:52:00: BR0:1 LCP: MRRU 1524 (0x110405F4)
*Mar 1 00:52:00: BR0:1 LCP: EndpointDisc 1 Local (0x130D01617373697374656E7A61)
*Mar 1 00:52:02: BR0:1 LCP: TIMEout: Time 0x300800 State REQsent
*Mar 1 00:52:02: BR0:1 LCP: O CONFREQ [REQsent] id 57 len 32
*Mar 1 00:52:02: BR0:1 LCP: AuthProto CHAP (0x0305C22305)
*Mar 1 00:52:02: BR0:1 LCP: MagicNumber 0x607750A1 (0x0506607750A1)
*Mar 1 00:52:02: BR0:1 LCP: MRRU 1524 (0x110405F4)
*Mar 1 00:52:02: BR0:1 LCP: EndpointDisc 1 Local (0x130D01617373697374656E7A61)
*Mar 1 00:52:03: %ISDN-6-CONNECT: Interface BRI0:1 is now connected to ....
The client is Windows XP and it is configured as usual
TIA
05-17-2002 08:26 AM
Router 1000 series is not capable to handle the modem calls over bri lines..It dosen't have the modem built in on which the modem calls can be terminated on..So it will not work.
It will only accept isdn calls over isdn line..
Pl. visit here for more information
05-17-2002 11:03 AM
Why do the connection complete successfully at the L1 level ?
From the debug it seems that the problem is with the ppp authentication negotiation
thanks
05-17-2002 03:13 PM
The connection will complete at the isdn layer..(regardless of the call type which is determined by " Bearer capability" in the SETUP message)..The problem is with the resources..ISDN call will be terminated on the hdlc controllers while the Async (modem) call needs to be terminated on the modem..Which 1003 dosen't have it.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide