PROBLEM UPGRADING TO MSFC2

Leonardo Pena Davila · ‎10-14-2004

Hi I've upgrade the MSFC card on the supervisor to MSFC2 but it doesn't recognize the new msfc2 card. I guess I did all in the right way but maybe I have missed one step. I upgraded the DRAM memory to 128MB, I upgraded the IOS to the cat6000-supk8.8-3-3.bin version I aligned the conectors in the supervisor engine, this is basycally what I did.

Can I get some help to solve my problem?

Thanks a lot

Regards

LP

es-plcdatacanter1> (enable) sh mod

Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

2 2 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

3 3 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no other

4 4 48 10/100/1000BaseT Ethernet WS-X6548-GE-TX yes ok

5 5 8 1000BaseX Ethernet WS-X6408-GBIC no ok

6 6 8 1000BaseX Ethernet WS-X6408-GBIC no ok

Mod Module-Name Serial-Num

--- -------------------- -----------

2 SAD0401051F

3 SAD035201LA

4 SAD083009DZ

5 JAB040205VJ

6 JAB040205X9

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

2 00-30-f2-70-30-66 to 00-30-f2-70-30-67 3.1 5.3(1) 8.3(3)

00-30-f2-70-30-64 to 00-30-f2-70-30-65

00-d0-00-a0-38-00 to 00-d0-00-a0-3b-ff

3 00-d0-bc-f2-a9-f8 to 00-d0-bc-f2-aa-27 1.1 4.2(0.24)V 8.3(3)

4 00-03-32-31-67-44 to 00-03-32-31-67-73 10.1 7.2(1) 8.3(3)

5 00-30-a3-38-52-1c to 00-30-a3-38-52-23 2.3 4.2(0.24)V 8.3(3)

6 00-30-a3-38-52-0c to 00-30-a3-38-52-13 2.3 4.2(0.24)V 8.3(3)

Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw

--- ----------------------- ------------------- ----------- ------ ------

2 L3 Switching Engine WS-F6K-PFC SAD035202KK 1.0

4 Inline Power Module WS-F6K-VPWR-GE SAD08320A5P 1.1 1.1(1)

sh version

WS-C6509 Software, Version NmpSW: 8.3(3)

NMP S/W compiled on Aug 9 2004, 02:27:17

System Bootstrap Version: 5.3(1)

System Boot Image File is 'bootflash:cat6000-supk8.8-3-3.bin'

System Configuration register is 0x102

Hardware Version: 2.0 Model: WS-C6509 Serial #: SCA040201D6

Prashanth Krishnappa · ‎10-14-2004

The MSFC2 might be in rommon. Issue a "switch console" from a console session and try to recover. The following page should help

http://www.cisco.com/warp/public/473/124.html

Leonardo Pena Davila · ‎10-14-2004

Thanks a lot I've solved my problem. Now my prompt is somethinmg like Router(boot). How can I fix it?

Once again Thanks!

Prashanth Krishnappa · ‎10-14-2004

Issue a "dir bootflash:" and see if you have a IOS file which starts with file name "c6msfc2-xxxxxx.bin".

If you do, set a boot variable using command

conf t

boot system flash bootflash:c6msfc2-xxxxxx.bin

config-register 0x2102

end

wr mem

If you reload at this point, it should boot up with full functional IOS. If you do not have an IOS image in bootflash, TFTP one into the bootflash.

Leonardo Pena Davila · ‎10-15-2004

Once again thanks a lot for your time. I've solved my problems I really appreciate that! Muchas gracias