Hi all,
I need to expand channel capacity up to 2 gbps. So I made a port-channel from the SCE to the router.
But I can't increase the bandwidth above 1Gbps, I thought maybe I have something incorrectly configured. Can you watch the correct settings are on my picture below?
Router:
Port-channel4 is up, line protocol is up
Hardware is GEChannel, address is 2894.0fed.ccc3 (bia 2894.0fed.ccc3)
Description: SCE subscribers
Internet address is 10.2.31.253/30
MTU 1500 bytes, BW 2000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 11/255, rxload 73/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
ARP type: ARPA, ARP Timeout 04:00:00
No. of active members in this channel: 2
Member 0 : GigabitEthernet2/0/5 , Full-duplex, 1000Mb/s
Member 1 : GigabitEthernet3/0/5 , Full-duplex, 1000Mb/s
No. of PF_JUMBO supported members in this channel : 3
Last input 00:57:18, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/750/0/0 (size/max/drops/flushes); Total output drops: 2605
Queueing strategy: fifo
Output queue: 0/80 (size/max)
5 minute input rate 577329000 bits/sec, 59453 packets/sec
5 minute output rate 86990000 bits/sec, 40119 packets/sec
598951426100 packets input, 739387565721756 bytes, 0 no buffer
Received 19 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 4 multicast, 0 pause input
489232530256 packets output, 104386916623678 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
SCE running-conf:
interface LineCard 0
aggregative-global-controllers
aggregative-global-controller-dynamic mode suspend
aggregative-global-controller-dynamic mode active
connection-mode inline on-failure bypass
no silent
no shutdown
service-bandwidth-prioritization-mode global
no protocol-pack version
flow-filter partition name "ignore_filter" first-rule 4 num-rules 32
flow-filter partition name "udpPortsToOpenBySw" first-rule 40 num-rules 21
attack-filter subscriber-notification ports 80
replace spare-memory code bytes 3145728
interface FastEthernet 0/0
ip address 10.10.7.155 255.255.255.0
interface FastEthernet 0/1
ip address 10.10.7.155 255.255.255.0
interface GigabitEthernet 0/1
auto-negotiate
interface GigabitEthernet 0/2
auto-negotiate
interface GigabitEthernet 0/3
auto-negotiate
interface GigabitEthernet 0/4
auto-negotiate
SCE:
SCE02#>sh int LineCard 0 link-to-port-mappings
Link Id | Upstream Port (Subscribers) | Downstream Port (Network)
---------------------------------------------------------------------------
0 | 0/1 | 0/2
1 | 0/3 | 0/4
SCE02#>sh int LineCard 0 link mode
Link mode on GBE1-GBE2
Current link mode is : forwarding
Actual link mode on active is : forwarding
Actual link mode on failure is: monopath-bypass
Link mode on GBE3-GBE4
Current link mode is : forwarding
Actual link mode on active is : forwarding
Actual link mode on failure is: monopath-bypass
SCE02#>sh int LineCard 0 physically-connected-links
slot 0 is connected to link-0 and link-1
SCE02#><eCard 0 aggregative-global-controllers-dynamic mode
AGC mode : active
SCE02#><global-controllers-dynamic side network dynamic-agc 0
Dynamic-AGCs : 0
side : subscriber
CIR : 0 Kb/sec
PIR : 2000000 Kb/sec
AL : 5
Name :
Parent : NULL
Enforce-Rate : 2000000 Kb/sec
Actual-Rate : 0 Kb/sec
Is Default : 1
SCE02#><l-controllers-dynamic side subscriber dynamic-agc 0
Dynamic-AGCs : 0
side : network
CIR : 0 Kb/sec
PIR : 2000000 Kb/sec
AL : 5
Name :
Parent : NULL
Enforce-Rate : 2000000 Kb/sec
Actual-Rate : 0 Kb/sec
Is Default : 1
