11-10-2016 06:31 AM - edited 03-03-2019 08:23 AM
Hi,
I have the cisco switch 4948 with bellow details and i mark in red the message that are important to check.
Please advice what are the root cause at this situation and how it can be fix.
Thank you in advance for time and answer.
Regards,
Toni
**********************************************************
*
* Welcome to Rom Monitor for WS-C4948E System *
* Copyright (c) 2003-2011 by Cisco Systems, Inc. *
* All rights reserved. *
* *
**********************************************************
Checking the partition table and boot sector...
Checking FAT, Files and Directories...
Reclaiming unused space...
Updating FAT...
Primary Rom Monitor Version 12.2(44r)SG11 CPU Rev: 3.1, Board Rev: 8,
Board Type: 104, CPLD Hobgoblin Rev: 21
Chassis: WS-C4948E
Front Panel Phy is Bcm5482s
Got Mac Address: 58:97:bd:8b:4f:bf
MAC Address : 58-97-bd-8b-4f-bf
Ip Address : Not set.
Netmask : Not set.
Gateway : Not set.
TftpServer : Not set.
Peer supervisor not detected or is not running IOS Supervisor uplinks
and all linecards have been reset
***** The system will autoboot in 5 seconds *****
Type control-C to prevent autobooting.
. . . . .
******** The system will autoboot now ********
config-register = 0x2101
Autobooting using the first file from bootflash.....
Rommon reg: 0x00004780
Reset2Reg: 0x00009EFF
##
Fortooine controller 0x0B5C66C8..0x0B72EC3F original size:0x001C685D
################## Decompression done, relocating ...
diagsk5 version 5.0.2.3
prod: WS-C4948E part: 73-14926-01 serial: CAT1936S2XC
Power-on-self-test for Module 1: WS-C4948E
CPU Subsystem Tests ...
seeprom: Pass
Traffic: L3 Looopback ...
Test Results: Pass
Traffic: L2 Loopback ...
Test Results: Pass
Switching Subsystem Memory ...
Packet Memory Test Results: Pass
Module 1 Passed
Rommon reg: 0x00000780
######################################################################
Decompression done, relocating ...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is subject to
restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted Rights clause at
FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer Software
clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, Catalyst 4500 L3 Switch Software
(cat4500e-ENTSERVICES-M), Version 15.1(2)SG5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Mon 03-Nov-14 09:38 by prod_rel_team
**********************************************************************
!!!! NO SUPPORTED POWER SUPPLIES DETECTED ON LOCAL SUPERVISOR SUPERVISOR WILL BE
POWERED DOWN!!!!
**********************************************************************
Powering down in 10 seconds...
10 09 08 07 06 05 04 03 02 01 00
11-10-2016 12:00 PM
What is the model of power supply you are using? Can you please check the below installation guide and make sure you are running a compatible power supply for 4948-E?
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4900/4948E/installation/guide/4948E_ins/04frus.html
Regards,
Kallol
07-17-2018 11:58 PM
Hello All,
yes thats right the power supply has to be "PWR-C49E-300AC-R"
even i have faced the same issue as my 4948E switch contained just "PWR-C49E-300AC" so the switch will shutdown,,,,, please try with PWR-C49E-300AC-R"
I hope this helps.........
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide