Unknown Trap OID: 1.3.6.1.4.1.9.6.1

[barry.patterson]

Which MIB provides trap definition for OID 1.3.6.1.4.1.9.6.1 received from CISCO ASR model 1002. (see below)

Unknown Trap OID: 1.3.6.1.4.1.9.6.1
Trap var bind data:
OID:  1.3.6.1.2.1.1.3.0  Value:  409790522
OID:  1.3.6.1.6.3.1.1.4.1.0  Value:  1.3.6.1.4.1.9.0.1
OID:  1.3.6.1.4.1.9.2.9.3.1.1.2.1  Value:  6
OID:  1.3.6.1.2.1.6.13.1.1.10.90.255.12.22.172.22.23.69.53094  Value:  8
OID:  1.3.6.1.4.1.9.2.6.1.1.5.10.90.255.12.22.172.22.23.69.53094  Value:  350
OID:  1.3.6.1.4.1.9.2.6.1.1.1.10.90.255.12.22.172.22.23.69.53094  Value:  0
OID:  1.3.6.1.4.1.9.2.6.1.1.2.10.90.255.12.22.172.22.23.69.53094  Value:  19

[bersoare]

Hi,

Could you post your running config?

Also, what SW version are you using?

You might have traps configured for these specific OIDs.

Thanks.

[barry.patterson]

Cisco IOS XE Software, Version 16.04.01

Cisco IOS Software [Everest], ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 16.4.1, RELEASE SOFTWARE (fc2)

SNMP config

snmp-server view *ilmi system included
snmp-server community xxxxxxxxxxxx RO
snmp-server community xxxxxxxxxxxx RW
snmp-server trap-source GigabitEthernet0
snmp-server location TDC - Row 1 Rack 2
snmp-server enable traps snmp authentication linkdown linkup coldstart warmstart
snmp-server enable traps tty
snmp-server enable traps ospf state-change
snmp-server enable traps ospf errors
snmp-server enable traps ospf retransmit
snmp-server enable traps ospf lsa
snmp-server enable traps ospf cisco-specific state-change nssa-trans-change
snmp-server enable traps ospf cisco-specific state-change shamlink interface
snmp-server enable traps ospf cisco-specific state-change shamlink neighbor
snmp-server enable traps ospf cisco-specific errors
snmp-server enable traps ospf cisco-specific retransmit
snmp-server enable traps ospf cisco-specific lsa
snmp-server enable traps casa
snmp-server enable traps bgp
snmp-server enable traps config-copy
snmp-server enable traps config
snmp-server enable traps dial
snmp-server enable traps diameter
snmp-server enable traps dlsw
snmp-server enable traps fru-ctrl
snmp-server enable traps entity
snmp-server enable traps event-manager
snmp-server enable traps frame-relay multilink bundle-mismatch
snmp-server enable traps frame-relay
snmp-server enable traps frame-relay subif
snmp-server enable traps hsrp
snmp-server enable traps ipmulticast
snmp-server enable traps msdp
snmp-server enable traps pim neighbor-change rp-mapping-change invalid-pim-message
snmp-server enable traps cpu threshold
snmp-server enable traps rsvp
snmp-server enable traps ipsla
snmp-server enable traps syslog
snmp-server enable traps flash insertion removal
snmp-server enable traps srp
snmp-server enable traps sonet
snmp-server enable traps mpls ldp
snmp-server enable traps mpls traffic-eng
snmp-server enable traps ike policy add
snmp-server enable traps ike policy delete
snmp-server enable traps ike tunnel start
snmp-server enable traps ike tunnel stop
snmp-server enable traps ipsec cryptomap add
snmp-server enable traps ipsec cryptomap delete
snmp-server enable traps ipsec cryptomap attach
snmp-server enable traps ipsec cryptomap detach
snmp-server enable traps ipsec tunnel start
snmp-server enable traps ipsec tunnel stop
snmp-server enable traps ipsec too-many-sas
snmp-server enable traps alarms informational
snmp-server enable traps voice poor-qov
snmp-server enable traps rf
snmp-server enable traps mpls vpn
snmp-server host xxxxxxxxxxxxx version 2c xxxxxxxxxxx
snmp-server host xxxxxxxxxxxxx version 2c xxxxxxxxxxx

[bersoare]

Just done a quick research, and it looks like this OID refers to the OLD-CISCO-TCP-MIB:

ftp://ftp.cisco.com/pub/mibs/v1/OLD-CISCO-TCP-MIB.my

Try disabling traps for TTY:

no snmp-server enable traps tty