WICs ON 2651XM

[volneicaetano]

I have three differet WIC's (1 dsu T1 V2) to be installed on a 2651XM.

I tried to install one at the time (in two different routers) and they never appear.

None of them is shown in the configuration.

the result for show interface shows only the two Fa interfaces.

IOS = Version 12.3(4)T3

Any idea? Is there any configuration that need to be done?

[thisisshanky]

Can you type a show version and paste the output here ? They are definitely supported on your platform.

http://www.cisco.com/en/US/products/hw/modules/ps3129/products_tech_note09186a0080093d70.shtml

Also can you log the boot sequence of the router with the module inserted ..

[volneicaetano]

I send it as soon as I have access to the router. Tomorrow morning.

Thanks,

[volneicaetano]

Boot sequence:

PS.:I deleted some information like Cisco Address, restrictions, and others bla-bla-bla.

System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

Copyright (c) 2003 by cisco Systems, Inc.

C2600 platform with 131072 Kbytes of main memory

program load complete, entry point: 0x80008000, size: 0x13611c8

Self decompressing the image : #....# [OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

00036F 0X00103980 C2651XM Dual Fast Ethernet

000149 0X00016804 Virtual Private Network (VPN) Module

0X000F3BB0 public buffer pools

0X00211000 public particle pools

TOTAL: 0X0041ED34

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Rounded IOMEM up to: 5Mb.

Using 3 percent iomem. [5Mb/128Mb]

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IK9O3S-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT

RELEASE SOFTWARE (fc2)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Fri 26-Sep-03 01:09 by eaarmas

Image text-base: 0x80008098, data-base: 0x81D502C8

cisco 2651XM (MPC860P) processor (revision 0x200) with 125952K/5120K bytes of me

mory.

Processor board ID JAE08010AVE (3158104672)

M860 processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

1 Virtual Private Network (VPN) Module(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

[volneicaetano]

Show version command:

Cisco Internetwork Operating System Software

IOS (tm) C2600 Software (C2600-IK9O3S-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT

RELEASE SOFTWARE (fc2)

TAC Support: http://www.cisco.com/tac

Copyright (c) 1986-2003 by cisco Systems, Inc.

Compiled Fri 26-Sep-03 01:09 by eaarmas

Image text-base: 0x80008098, data-base: 0x81D502C8

ROM: System Bootstrap, Version 12.2(8r) [cmong 8r], RELEASE SOFTWARE (fc1)

ROM: C2600 Software (C2600-IK9O3S-M), Version 12.2(15)ZJ3, EARLY DEPLOYMENT RELE

ASE SOFTWARE (fc2)

progroup uptime is 12 minutes

System returned to ROM by power-on

System image file is "flash:c2600-ik9o3s-mz.122-15.ZJ3.bin"

cisco 2651XM (MPC860P) processor (revision 0x200) with 125952K/5120K bytes of me

mory.

Processor board ID JAE08010AVE (3158104672)

M860 processor: part number 5, mask 2

Bridging software.

X.25 software, Version 3.0.0.

2 FastEthernet/IEEE 802.3 interface(s)

1 Virtual Private Network (VPN) Module(s)

32K bytes of non-volatile configuration memory.

32768K bytes of processor board System flash (Read/Write)

Configuration register is 0x2102

[Kevin Dorrell]

This may be a silly question, but I shall ask it anyway: did you switch off the router before you installed the WICs? 'Cos unlike some systems, they are not hot-swap, and can actually be damaged by trying to hot-swap them.

Kevin Dorrell

Luxembourg

[volneicaetano]

It is not a silly question. But I did install them with no power in the router(s). You kind answered my question, I was affraid that the cards came damaged. They were bought on-line (eBay or similar)and you never know.

THanks for your reply,

Volnei

[thisisshanky · Accepted solution]

In your boot sequence, I was intersted in looking at the SYslog messages that appear immediately after the output that you have posted. It usually indicates if the card cannot be detected "Undefined port adapter" or something similar.. It is possible that the card was DOA, your best bet is to call the ebay seller and ask for a replacement.

I would also try the following. Check if you have properly seated them in the WIC slot. If you have any spare working WICs, check to see if the router's slot is good.

Try giving this command, "memory-size iomem 10" and see if that helps in any way. All it does is allocates a percentage of memory to the interfaces/network modules.

[volneicaetano]

Press RETURN to get started!

That is the rest of the message.

I have one WIC card to test (which is not V2) but it is production now. I will be able to test only tomorrow.

I have two routers and 3 WICs I tested all combinations and none of them worked.

I really think the Cards are damaged. I will contact the seller.

Volnei

[volneicaetano]

I updated the IOS from 12.2(15)ZJ3 to 12.3(4)T3. It is working now.

Thank you for your help.