10-17-2010 11:16 PM - edited 03-03-2019 06:05 AM
Hi,
Been pulling my hair out on this one!! OK in my lab environment I have a hub (R1) & spoke (R2 and R3) network with a frame relay switch (R6). For some reason, I am seeing CISCO, status deleted on the spoke routers. This is not allowing me to PING. Here's a quick look at all the configurations;
R6 - Frame Relay Switch
interface Serial0
no ip address
encapsulation frame-relay
logging event subif-link-status
logging event dlci-status-change
clock rate 56000
no fair-queue
no frame-relay inverse-arp
frame-relay intf-type dce
frame-relay route 122 interface Serial1 221
frame-relay route 123 interface Serial2 321
!
interface Serial1
no ip address
encapsulation frame-relay
logging event subif-link-status
logging event dlci-status-change
clock rate 56000
no frame-relay inverse-arp
frame-relay intf-type dce
frame-relay route 221 interface Serial0 122
!
interface Serial2
no ip address
encapsulation frame-relay
logging event subif-link-status
logging event dlci-status-change
clock rate 56000
no frame-relay inverse-arp
frame-relay intf-type dce
frame-relay route 321 interface Serial0 123
R6#show frame-relay route
Input Intf Input Dlci Output Intf Output Dlci Status
Serial0 122 Serial1 221 active
Serial0 123 Serial2 321 active
Serial1 221 Serial0 122 active
Serial2 321 Serial0 123 active
R1 - Hub
R1#show run int serial 0/1
Building configuration...
Current configuration : 214 bytes
!
interface Serial0/1
ip address 172.0.123.1 255.255.255.248
encapsulation frame-relay
frame-relay map ip 172.0.123.2 122 broadcast
frame-relay map ip 172.0.123.3 123 broadcast
no frame-relay inverse-arp
end
R1#show frame-relay map
Serial0/1 (up): ip 172.0.123.2 dlci 122(0x7A,0x1CA0), static,
broadcast,
CISCO, status defined, active
Serial0/1 (up): ip 172.0.123.3 dlci 123(0x7B,0x1CB0), static,
broadcast,
CISCO, status defined, active
R1#show frame-relay pvc
PVC Statistics for interface Serial0/1 (Frame Relay DTE)
Active Inactive Deleted Static
Local 2 0 0 0
Switched 0 0 0 0
Unused 0 0 0 0
R2 - Spoke
R2#show run interface serial 0/0
Building configuration...
Current configuration : 258 bytes
!
interface Serial0/0
ip address 172.0.123.2 255.255.255.248
encapsulation frame-relay
fair-queue
frame-relay map ip 172.0.123.1 221 broadcast
frame-relay map ip 172.0.123.3 221 broadcast
frame-relay interface-dlci 221
no frame-relay inverse-arp
end
R2#show frame-relay map
Serial0/0 (up): ip 172.0.123.1 dlci 221(0xDD,0x34D0), static,
broadcast,
CISCO, status deleted
Serial0/0 (up): ip 172.0.123.3 dlci 221(0xDD,0x34D0), static,
broadcast,
CISCO, status deleted
R2#show frame-relay pvc
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
Active Inactive Deleted Static
Local 0 0 1 0
Switched 0 0 0 0
Unused 1 0 0 0
R3 - Spoke
R3#show run int ser0/0
Building configuration...
Current configuration : 261 bytes
!
interface Serial0/0
ip address 172.0.123.3 255.255.255.248
encapsulation frame-relay
no fair-queue
frame-relay map ip 172.0.123.1 321 broadcast
frame-relay map ip 172.0.123.2 321 broadcast
frame-relay interface-dlci 321
no frame-relay inverse-arp
end
R3#show frame-relay map
Serial0/0 (up): ip 172.0.123.1 dlci 321(0x141,0x5010), static,
broadcast,
CISCO, status deleted
Serial0/0 (up): ip 172.0.123.2 dlci 321(0x141,0x5010), static,
broadcast,
CISCO, status deleted
R3#show frame-relay pvc
PVC Statistics for interface Serial0/0 (Frame Relay DTE)
Active Inactive Deleted Static
Local 0 0 1 0
Switched 0 0 0 0
Unused 1 0 0 0
Am I forgetting something??
Thanks
DK