11-05-2014 05:12 AM - edited 03-05-2019 12:06 AM
Hi,
I have 6509 with two 3000kw power supply, but when I show power and check the system logs, power supply in slot 1 does not been identified. Who can help me solve this problem? Thanks.
-------------------------
C6509#show power
system power redundancy mode = redundant
system power total = 2771.16 Watts (65.98 Amps @ 42V)
system power used = 466.20 Watts (11.10 Amps @ 42V)
system power available = 2304.96 Watts (54.88 Amps @ 42V)
Power-Capacity PS-Fan Output Oper
PS Type Watts A @42V Status Status State
---- ------------------ ------- ------ ------ ------ -----
1 unknown 919.38 21.89 ?? ?? on
2 WS-CAC-3000W 2771.16 65.98 OK OK on
Pwr-Allocated Oper
Fan Type Watts A @42V State
---- ------------------ ------- ------ -----
1 WS-C6509-E-FAN 150.36 3.58 OK
Pwr-Requested Pwr-Allocated Admin Oper
Slot Card-Type Watts A @42V Watts A @42V State State
---- ------------------ ------- ------ ------- ------ ----- -----
5 WS-SUP32-GE-3B 154.98 3.69 154.98 3.69 on on
6 (Redundant Sup) - - 154.98 3.69 - -
system auxiliary power mode = off
system auxiliary power redundancy operationally = non-redundant
system primary connector power limit = 10920.00 Watts (260.00 Amps @ 42V)
system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V)
system primary power used = 466.20 Watts (11.10 Amps @ 42V)
system auxiliary power used = 0 Watt
-------------------------------
*Mar 30 08:24:53.923: RP: Currently running ROMMON from S (Gold) region
*Mar 30 08:24:59.691: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 30 08:25:04.191: %SYS-5-RESTART: System restarted --
Cisco IOS Software, s3223_rp Software (s3223_rp-ADVENTERPRISE_WAN-M), Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 22-Jun-11 17:11 by prod_rel_team
*Mar 30 07:15:12.811: %SYS-3-LOGGER_FLUSHED: System was paused for 00:00:00 to ensure console debugging output.
*Mar 30 08:25:03.439: %C6KPWR-SP-3-PSUNKNOWN: Unknown power supply in slot 1 (idprom read failed).
*Mar 30 08:25:03.439: %SYS-SP-5-RESTART: System restarted --
Cisco IOS Software, s3223_sp Software (s3223_sp-ADVENTERPRISE_WAN-M), Version 12.2(33)SXJ1, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Wed 22-Jun-11 17:46 by prod_rel_team
*Mar 30 08:25:03.463: SP: Currently running ROMMON from S (Gold) region
*Mar 30 08:25:03.463: %OIR-SP-6-INSPS: Power supply inserted in slot 1
*Mar 30 08:25:04.331: %C6KPWR-SP-4-PSOK: power supply 1 turned on.
*Mar 30 08:25:04.399: %OIR-SP-6-INSPS: Power supply inserted in slot 2
*Mar 30 08:25:04.399: %C6KPWR-SP-4-PSOK: power supply 2 turned on.
*Mar 30 08:25:04.403: %C6KPWR-SP-4-PSREDUNDANTMISMATCH: power supplies rated outputs do not match.
*Mar 30 08:25:04.403: %C6KPWR-SP-4-PSREDUNDANTBOTHSUPPLY: in power-redundancy mode, system is operating on both power supplies.
*Mar 30 08:25:05.627: %SNMP-5-COLDSTART: SNMP agent on host C6509 is undergoing a cold start
*Mar 30 08:25:07.263: %DIAG-SP-6-RUN_MINIMUM: Module 5: Running Minimal Diagnostics...
*Mar 30 08:25:34.107: %DIAG-SP-6-DIAG_OK: Module 5: Passed Online Diagnostics
*Mar 30 08:25:35.195: %MFIB_CONST_RP-6-REPLICATION_MODE_CHANGE: Replication Mode Change Detected. Current system replication mode is Ingress