Hi I'm setting up a Cisco 887 ADSL/VDSL router at home.
I have the ADSL2+ Annex A side up and running.
Cisco_887#show ip int brief
Interface IP-Address OK? Method Status Protocol
ATM0 unassigned YES NVRAM up up
BRI0 unassigned YES NVRAM administratively down down
BRI0:1 unassigned YES unset administratively down down
BRI0:2 unassigned YES unset administratively down down
Dialer1 (omitted) YES IPCP up up
FastEthernet0 unassigned YES unset up up
FastEthernet1 unassigned YES unset up up
FastEthernet2 unassigned YES unset up down
FastEthernet3 unassigned YES unset up down
NVI0 unassigned YES unset administratively down down
SSLVPN-VIF0 unassigned NO unset up up
Virtual-Access1 unassigned YES unset up up
Virtual-Access2 unassigned YES unset up up
Vlan1 192.168.1.1 YES NVRAM up up
Cisco_887#
Cisco_887#show dsl int atm0
ATM0
Alcatel 20190 chipset information
ATU-R (DS) ATU-C (US)
Modem Status: Showtime (DMTDSL_SHOWTIME)
DSL Mode: ITU G.992.5 (ADSL2+) Annex A
ITU STD NUM: 0x03 0x2
Chip Vendor ID: 'STMI' 'IKNS'
Chip Vendor Specific: 0x0000 0x0001
Chip Vendor Country: 0x0F 0xB5
Modem Vendor ID: 'CSCO' 'IKNS'
Modem Vendor Specific: 0x0000 0x0000
Modem Vendor Country: 0xB5 0xB5
Serial Number Near: FHK135273SQ
Serial Number Far: ^A
Modem VeChip ID: C196 (3) capability-enabled
DFE BOM: DFE3.0 Annex A (1)
Capacity Used: 99% 65535%
Noise Margin: 11.5 dB 12.0 dB
Output Power: 19.0 dBm 12.5 dBm
Attenuation: 41.0 dB 18.0 dB
FEC ES Errors: 0 6993
ES Errors: 0 78632
SES Errors: 0 250
LOSES Errors: 0 21
UES Errors: 0 135
Defect Status: None None
Last Fail Code: None
Watchdog Counter: 0x69
Watchdog Resets: 0
Selftest Result: 0x00
Subfunction: 0x00
Interrupts: 12372 (0 spurious)
PHY Access Err: 0
Activations: 1
LED Status: ON
LED On Time: 100
LED Off Time: 100
Init FW: init_AMR-4.0.015_no_bist.bin
Operation FW: AMR-4.0.015.bin
FW Source: embedded
FW Version: 4.0.15
DS Channel1 DS Channel0 US Channel1 US Channel0
Speed (kbps): 0 8763 0 1093
Cells: 0 406 0 6159740
Reed-Solomon EC: 0 0 0 13844
CRC Errors: 0 565 0 79449
Header Errors: 0 509 0 0
Total BER: 0E-0 33280E-0
Leakage Average BER: 0E-0 33280E-0
Interleave Delay: 0 36 0 8
ATU-R (DS) ATU-C (US)
Bitswap: enabled enabled
Bitswap success: 0 0
Bitswap failure: 0 0
LOM Monitoring : Disabled
DMT Bits Per Bin
000: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
010: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
020: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
030: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 3 0
040: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
050: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
060: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
070: 0 0 0 0 0 0 0 0 0 0 3 0 0 0 3 0
080: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
090: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
0A0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
0B0: 0 0 6 0 0 0 A 9 0 0 4 5 0 0 4 5
0C0: 0 0 4 5 0 0 4 5 0 0 4 5 0 0 4 5
0D0: 0 0 4 5 0 0 3 0 0 0 3 0 0 0 3 0
0E0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
0F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
100: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
110: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
120: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
130: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 0 0
140: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
150: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
160: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
170: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 3 0
180: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
190: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
1A0: 0 0 3 0 0 0 3 0 0 0 3 0 0 0 3 0
1B0: 0 0 2 0 0 0 7 0 0 0 0 0 0 0 0 0
1C0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1D0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1E0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
1F0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DSL: Training log buffer capability is not enabled
Cisco_887#
I can ping outside IP addresses from the router
Cisco_887#ping 202.89.4.222
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 202.89.4.222, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 16/16/20 ms
Cisco_887#
But no computers can access the internet and I think I know why:
Cisco_887#show ip int atm0
ATM0 is up, line protocol is up
Internet protocol processing disabled
Cisco_887#
How can I make that say enabled?
