Hi Team,
We are using Cisco 3850 Poe - 24 port Switch. i have connected Cisco AP's with Each port. we are trying to get 8 APs powered up using POE from Cisco 3850 and only some are coming up. remaining Ports are down not providing power to AP's
we have done factory reset to switch - after that also not powered up
Pls find the below SHow power inline output
I#show power inline
Module Available Used Remaining
(Watts) (Watts) (Watts)
------ --------- -------- ---------
1 720.0 0.0 720.0
Interface Admin Oper Power Device Class Max
(Watts)
--------- ------ ---------- ------- ------------------- ----- ----
Gi1/0/1 auto off 0.0 n/a n/a 30.0
Gi1/0/2 auto off 0.0 n/a n/a 30.0
Gi1/0/3 auto off 0.0 n/a n/a 30.0
Gi1/0/4 auto off 0.0 n/a n/a 30.0
Gi1/0/5 auto off 0.0 n/a n/a 30.0
Gi1/0/6 auto off 0.0 n/a n/a 30.0
Gi1/0/7 auto off 0.0 n/a n/a 30.0
Gi1/0/8 auto off 0.0 n/a n/a 30.0
Gi1/0/9 auto off 0.0 n/a n/a 30.0
Gi1/0/10 auto off 0.0 n/a n/a 30.0
Gi1/0/11 auto off 0.0 n/a n/a 30.0
Gi1/0/12 auto off 0.0 n/a n/a 30.0
Gi1/0/13 off off 0.0 n/a n/a 30.0
Gi1/0/14 off off 0.0 n/a n/a 30.0
Gi1/0/15 off off 0.0 n/a n/a 30.0
Gi1/0/16 off off 0.0 n/a n/a 30.0
Gi1/0/17 off off 0.0 n/a n/a 30.0
Gi1/0/18 off off 0.0 n/a n/a 30.0
Gi1/0/19 off off 0.0 n/a n/a 30.0
Gi1/0/20 off off 0.0 n/a n/a 30.0
Gi1/0/21 off off 0.0 n/a n/a 30.0
Gi1/0/22 off off 0.0 n/a n/a 30.0
Gi1/0/23 off off 0.0 n/a n/a 30.0
Gi1/0/24 off off 0.0 n/a n/a 30.0
All of my Oper shows off state - how do i change it as - On state
switch Model and Image
Switch Ports Model SW Version SW Image Mode
------ ----- ----- ---------- ---------- ----
* 1 32 WS-C3850- 24P 03.03.04SE cat3k_caa-universalk9 INSTALL
>show power inline gigabitEthernet 1/0/7 detail
Interface: Gi1/0/7
Inline Power Mode: auto
Operational status: off
Device Detected: no
Device Type: n/a
IEEE Class: n/a
Discovery mechanism used/configured: Ieee and Cisco
Police: off
Power Allocated
Admin Value: 30.0
Power drawn from the source: 0.0
Power available to the device: 0.0
Actual consumption
Measured at the port: 0.0
Maximum Power drawn by the device since powered on: 0.0
Absent Counter: 0
Over Current Counter: 0
Short Current Counter: 0
Invalid Signature Counter: 0
Power Denied Counter: 0
Power Negotiation Used: CDP
LLDP Power Negotiation --Sent to PD-- --Rcvd from PD--
Power Type: - -
Power Source: - -
Power Priority: - -
Requested Power(W): - -
Allocated Power(W): - -
How do i on the oper in power inline
pls help me on it
Thanks,
Reagrds,
Yasmeen Shaul Hameed
