05-14-2023 06:49 AM
i got this device from my friend and it not booting so im trying to boot it from tftp and install nxos on it but i got this error and this is my device log :
CISCO SWITCH Ver7.17
Device detected on 0:6:0 after 0 msecs
Device detected on 0:1:1 after 0 msecs
Device detected on 0:1:0 after 0 msecs
MCFrequency 1600Mhz
Relocated to memory
Detected CISCO IOFPGA
Donner Present
MIFPGA Present
Code Signing Results: 0x0
Using Upgrade FPGA
Booting from Primary Bios
FPGA Revison : 0x6
FPGA ID : 0x1345727
FPGA Date : 0x20141015
Power Debug Register: 0x0
Reset Cause Register: 0x80000000
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20
Detected CISCO MIFPGA
Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.
Board type 2
IOFPGA @ 0xc8000000
SLOT_ID @ 0xf
Trying to read config file /boot/grub/menu.lst.local from (hd0,4)
Filesystem type is ext2fs, partition type 0x83
Trying to read config file /boot/grub/menu.lst.local from (hd0,5)
Filesystem type is ext2fs, partition type 0x83
No autoboot or failed autoboot. falling to loader
Loader Version 7.17
loader > set ip 192.168.100.121 255.255.255.0
Correct - ip addr is 192.168.100.121, mask is 255.255.255.0
Finding driver for NIC vendor 8086 Device 438
Found the device 8086:438 at ioaddr e000, membase d8200000 at 1:2
Probing...igb: e1000_set_media_typeMedia type is copper 00900c00
igb: e1000_set_media_typeMedia type is copper 00900c00
igb: INTEL MAC+PHY reset (ctrl 0x08d00240)
igb: INTEL p has large-format EERD
igb: INTEL has EEPROM MAC address
Ethernet addr: E0:0E:DA:2A:0C:D6
igb: INTEL link status is 0x80080747
Link is up
Link speed = 100 Mbps, Full Duplex
igb: e1000_init_rx_addrsigb: Programming MAC Address into RAR[0]
igb: Clearing RAR[1-15]
Tx: TDBAL: 0x7d739d80
TDLEN: 128
TCTL: 0x0003f0fa
TXDCTL: 0x02000000
TDH: 0x00000000
TDT: 0x00000000
tx_head=0x00000000, tx_tail = 0x00000000
Rx: RDBAL: 0x7d739c80
RDLEN: 128
RCTL: 0x04008002
RXDCTL: 0x02010a0c
RDH: 0x00000000
RXCSUM: 0x00000300
RDT: 0x00000007
igb: INTEL link status is 0x80080747
Link is up
Link speed = 100 Mbps, Full Duplex
CTRL: 0x08d00240
STATUS: 0x80080747
CTRL_EXT: 0x12900c00
TXCW: 0x00000000
RXCW: 0x00000000
TPR: 0x00000006
TPT: 0x00000000
EECD: 0x00004718
EERD: 0xd60c020a
FCAL: 0x00c28001
FCAH: 0x00000100
FCT: 0x00008808
VET: 0x81008100
FCTTV: 0x00000000
LEDCTL: 0xcf06cf02
PBA: 0x00000000
ICR: 0x00000004
ITR: 0x00000000
ICS: 0x00000000
IMS: 0x00000000
IMC: 0x00000000
RCTL: 0x04008002
FCRTL: 0x00000000
FCRTH: 0x00000000
RDBAL: 0x7d739c80
RDBAH: 0x00000000
RDLEN: 0x00000080
RDH: 0x00000000
RDT: 0x00000007
RDTR: 0x00000000
RADV: 0x00000000
RSRPD: 0x00000000
TCTL: 0x0003f0fa
TIPG: 0x00601008
TDBAL: 0x7d739d80
TDBAH: 0x00000000
TDLEN: 0x00000080
TDH: 0x00000000
TDT: 0x00000000
TIDV: 0x00000000
TXDMAC: 0x00000000
TXDCTL: 0x02000000
TADV: 0x00000000
TSPMT: 0x00000000
RXDCTL: 0x02010a0c
RXCSUM: 0x00000300
CONNSW: 0x00000600
PCS_CFG0: 0x00000008
PCS_LCTL: 0x0211000c
PCS_LSTS: 0x0063001b
PCS_ANADV: 0x000001a0
PCS_LPAB: 0x0000d400
Address: 192.168.100.121
Netmask: 255.255.255.0
Server: 0.0.0.0
Gateway: 0.0.0.0
loader > set gw 192.168.100.3
Correct gateway addr 192.168.100.3
Address: 192.168.100.121
Netmask: 255.255.255.0
Server: 0.0.0.0
Gateway: 192.168.100.3
loader > cmdline recoery=1
loader > boot tftp://192.168.100.3/nxos.9.3.7a.bin
Booting tftp://192.168.100.3/nxos.9.3.7a.bin
Trying netboot
Filename: /nxos.9.3.7a.bin
Address: 192.168.100.121
Netmask: 255.255.255.0
Server: 192.168.100.3
Gateway: 192.168.100.3
Filesystem type is tftp, using whole disk
..........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................Image valid
Image Signature verification was Successful.
image length: 512779264 bytes
Installing klm_card_index
done
Linking n9k flash devices
creating flash devices BOOT_DEV= sda
INIT: version 2.88 booting
Installing ata_piix module ... done.
Unsquashing rootfs ...
Total size needed in bootflash is 108800
check bootflash : OK
Total size needed in bootflash is 41192
check bootflash : OK
Enabling 8250 serial driver spurious INTs workaround
Installing isan procfs ... done.
is_lxc: is_titan_eor: is_stby: suffix: klm_ftrace: /isanboot/lib/modules/klm_ftrace.o
Installing ftrace in non-lxc mode done
Installing SSE module with card index 21025 ... done.
Creating SSE device node 247 ... done.
Loading I2C driver ... done.
Loading MEM scrub driver ... done.
Installing CCTRL driver for card_type 19 without NEED_GEM ... done.
Loading IGB driver ... done.
Not Micron SSD...
Checking all filesystems.Warning: switch is starting up with default configuration
**Warning** :Free memory available in /var/sysmgr/ftp is 2048 MB
need atleast 2GB space for RPM extraction via tftp/pxe boot ,run df -h
Installing SPROM driver ... 21025 IS_N9K done.
Installing pfmsvcs module ...done.
Installing nvram module ... done.
Installing if_index module with port mode 6 ... done.
Installing fcfwd
Installing RNI lcnd ... done
Installing LC netdev ... done
Installing psdev module ... done.
Installing veobc module ... done.
Checking SR card
Card Index is 21025
Inserting eMMC module ...
Inserting mtdphysmap module...Inserting OBFL module ... done.
Making OBFL character devices
mounting plog for N9k!
Mounting OBFL pstore for mtd
Inserting kernel_services module ... done.
Making kernel_services character devices
cgroups initialized
exit code: 1
tune2fs 1.42.9 (28-Dec-2013)
Setting reserved blocks percentage to 0% (0 blocks)
Starting portmap daemon...
creating NFS state directory: done
starting 8 nfsd kernel threads: done
starting mountd: done
starting statd: done
setup_ipv4_mgmt_int_cmos_or_dhcp
Cmos IP=192.168.100.121
Cmos gw=192.168.100.3
Cmos mask=255.255.255.0
Valid IP4 address 192.168.100.121
Valid IP4 gateway 192.168.100.3
eth1 Link encap:Ethernet HWaddr e0:0e:da:2a:0c:d6
inet addr:192.168.100.121 Bcast:192.168.100.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Sleeping for 120 seconds as management interface takes time to come up
eth1 Link encap:Ethernet HWaddr e0:0e:da:2a:0c:d6
inet addr:192.168.100.121 Bcast:192.168.100.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Saving image for img-sync ...
Low free space ,tftp download destination changed to bootflash
Enough free disk space found on bootflash
mv: missing destination file operand after '/bootflash/nxos.9.3.7a.bin'
Try 'mv --help' for more information.
not found. TFTP download failed, Pls diagnose your network problem first
Extracting rpms from image...
ls: cannot access /rpms/crdcfg_rpms/t2_tor_crdcfgdata-*.rpm: No such file or directory
ls: cannot access /wrl/: No such file or directory
Card index is 21025
Calling install_tor for TOR
ls: cannot access /rpms/tor_rpms/tor_n9k-*rpm: No such file or directory
ls: cannot access /rpms/tor_rpms/tor_n3k-*rpm: No such file or directory
ls: cannot access /rpms/tor_rpms/tor_n3500-*rpm: No such file or directory
ls: cannot access /rpms/tor_rpms/tor_fretta-*rpm: No such file or directory
ls: cannot access /rpms/tahusd_n9000-*rpm: No such file or directory
mkdir: cannot create directory '/lc': File exists
mount: special device /isanboot/bin/images/ins_tor_n9k.bin does not exist
Not Micron SSD...
Not Micron SSD...
Loading system software
Installing local RPMS
Patch Repository Setup completed successfully
Creating /dev/mcelog
Starting mcelog daemon
INIT: Entering runlevel: 3
Running S93thirdparty-script...
Populating conf files for hybrid sysmgr ...
Starting hybrid sysmgr ...
done
Netbroker support IS present in the kernel.
done
Skipping EMON in TOR ...
Executing Prune clis.
ethernet switching mode Wed May 9 23:16:48 UTC 2012
May 9 23:16:49 sysmgr: <<%SYSMGR-2-PARSEERR_INVALIDDEPEND>> /isan/etc/sysmgr.d.hybrid_lc/synctask4.conf:211 [from /isan/etc/sysmgr.conf.hybrid_lc:62] (in dependency list of service "lcdc3_syncpoint4"): service "xbar_client" not defined for scope "control".
May 9 23:16:49 %SYSMGR-2-PARSEERR_INVALIDDEPEND /isan/etc/sysmgr.d.hybrid_lc/synctask4.conf:211 [from /isan/etc/sysmgr.conf.hybrid_lc:62] (in dependency list of service "lcdc3_syncpoint4"): service "xbar_client" not defined for scope "control".
May 9 23:16:50 %FW_APP-2-FIRMWARE_IMAGE_LOAD_SUCCESS No Firmware needed for Non SR card.
2012 May 9 23:16:54 %$ VDC-1 %$ %USER-2-SYSTEM_MSG: <<%USBHSD-2-MOUNT>> logflash: online - usbhsd
2012 May 9 23:16:56 %$ VDC-1 %$ %CRDCFG-SLOT1-2-CRDCFG_SRV_CRIT: Error getting crd info:
2012 May 9 23:16:57 %$ VDC-1 %$ %CARDCLIENT-2-CARDCL_CRIT: cardcl_af_sync1_done: Failed to get card info
2012 May 9 23:16:57 %$ VDC-1 %$ %MODULE-2-MOD_DIAG_FAIL: Module 1 (Serial number: ) reported failure due to Card Configuration Request Failed in device DEV_LINECARD (device error 0x0)
2012 May 9 23:16:57 %$ VDC-1 %$ %USER-1-SYSTEM_MSG: ASSERT@../utils/usd/libusd/usd_drv.c:3226 - dc3_sensor
[▒
CISCO SWITCH Ver7.17
Device detected on 0:6:0 after 0 msecs
Device detected on 0:1:1 after 0 msecs
Device detected on 0:1:0 after 0 msecs
MCFrequency 1600Mhz
Relocated to memory
Detected CISCO IOFPGA
Donner Present
MIFPGA Present
Code Signing Results: 0x0
Using Upgrade FPGA
Booting from Primary Bios
FPGA Revison : 0x6
FPGA ID : 0x1345727
FPGA Date : 0x20141015
Power Debug Register: 0x0
Reset Cause Register: 0x4
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20
Detected CISCO MIFPGA
Version 2.16.1240. Copyright (C) 2013 American Megatrends, Inc.
Board type 2
IOFPGA @ 0xc8000000
SLOT_ID @ 0xf
Trying to read config file /boot/grub/menu.lst.local from (hd0,4)
Filesystem type is ext2fs, partition type 0x83
Trying to read config file /boot/grub/menu.lst.local from (hd0,5)
Filesystem type is ext2fs, partition type 0x83
No autoboot or failed autoboot. falling to loader
Loader Version 7.17
loader >