cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2528
Views
0
Helpful
8
Replies

cisco router 1941 not supporting IP SLA

ahemadt0544
Level 1
Level 1

Hi

I have cisco 1941 router , where i am not able configure below

ip sla auto discovery ip sla 1 icmp-echo 10.103.157.2 source-ip 10.103.157.1 threshold 2000 timeout 2000

present ios is : System image file is "flash0:c1900-universalk9-mz.SPA.154-3.M1.bin" please advice .

8 Replies 8

Aditya Ganjoo
Cisco Employee
Cisco Employee

Hi Ahmad,

Could you please share what error you are getting on this ?

As per the IOS you are running we should not be facing any issues with this.

May I know for which command you are getting the error ?

Regards,

Aditya

Hi Aditya ,

hw you doing , The problem am facing is below

I am going to replace cisco 881 Router with cisco 1941 Router in my office .

config 881.

ip sla auto discovery
ip sla 1 
 icmp-echo 10.103.157.2 source-ip 10.103.157.1
 threshold 2000
 timeout 2000
 frequency 5
ip sla schedule 1 life forever start-time now
ip sla 2 
 icmp-echo 10.100.100.50

the above configuration is not supported in my New cisco 1941 router .

Ip sla 1 is not support .

please advice there is any command support the same features or its IOS issue .

 

Hi Ahmed,

Share the show version of the new 1941 router.

Regards,

Aditya

Thanks in advance for your support .

Lala._zoor(config)#ip sla 1
                                   ^
% Invalid input detected at '^' marker.

Lala.al_kuwait_zoor(config)#icmp ?

hi

SH VERSION
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.4(3)M1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Sat 25-Oct-14 01:02 by prod_rel_team

ROM: System Bootstrap, Version 15.0(1r)M16, RELEASE SOFTWARE (fc1)

Lala.al_zoor uptime is 1 minute
System returned to ROM by power-on
System image file is "flash0:c1900-universalk9-mz.SPA.154-3.M1.bin"
Last reload type: Normal Reload
Last reload reason: power-on

 

This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
         
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
         
If you require further assistance please contact us by sending email to
export@cisco.com.
         
Cisco CISCO1941/K9 (revision 1.0) with 491520K/32768K bytes of memory.
Processor board ID FCZ191760TD
2 Gigabit Ethernet interfaces
1 terminal line
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
255488K bytes of ATA System CompactFlash 0 (Read/Write)
         
         
License Info:
         
License UDI:
         
-------------------------------------------------
Device#   PID                   SN
-------------------------------------------------
*1        CISCO1941/K9          FCZ191760TD    
         
         
         
Technology Package License Information for Module:'c1900'
         
------------------------------------------------------------------------
Technology    Technology-package                  Technology-package
              Current              Type           Next reboot 
------------------------------------------------------------------------
ipbase        ipbasek9             Permanent      ipbasek9
security      None                 None           None
data          None                 None           None
NtwkEss       None                 None           None
         
Configuration register is 0x2102

Hi Ahmed,

I do not see Security license enabled on the 1941 router.

We need to enable it to use this feature.

Hope it answers your query.

Regards,

Aditya

Hi Ahmed,

May i know has the issue been resolved ?

Regards,

Aditya

Please rate helpful posts.

HI ,

Can please advice , how to enable security license.

Should we pay to get license.

Hi Ahmed,

For enabling this license I would request you to contact your Accounts team.

Regards,

Aditya

Please rate helpful posts.