I've installed QuickVPN on Windows XP, configured an account on the router.
But when I'm trying to connect to the router I get the following:
MS NT5 ISAKMPOAKLEY 00000004]
Oct 2 06:25:33 - [VPN Log]: packet from 1.1.1.1:500: ignoring Vendor ID payload [FRAGMENTATION]
Oct 2 06:25:33 - [VPN Log]: packet from 1.1.1.1:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] method set to=106
Oct 2 06:25:33 - [VPN Log]: packet from 1.1.1.1:500: ignoring Vendor ID payload [Vid-Initial-Contact]
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: responding to Main Mode from unknown peer 1.1.1.1
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: Oakley Transform [OAKLEY_3DES_CBC (192), OAKLEY_SHA1, OAKLEY_GROUP_MODP1024] refused due to strict flag
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: transition from state STATE_MAIN_R0 to state STATE_MAIN_R1
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: STATE_MAIN_R1: sent MR1, expecting MI2
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike-02/03: no NAT detected
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: STATE_MAIN_R2: sent MR2, expecting MI3
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: Main mode peer ID is ID_IPV4_ADDR: '1.1.1.1'
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: I did not send a certificate because I do not have one.
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: STATE_MAIN_R3: sent MR3, ISAKMP SA established {auth=OAKLEY_PRESHARED_KEY cipher=oakley_3des_cbc_192 prf=oakley_md5 group=modp1024}
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: cannot respond to IPsec SA request because no connection is known for 192.168.160.0/24===2.2.2.2[S?C]...1.1.1.1[S?C]
Oct 2 06:25:33 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: sending encrypted notification INVALID_ID_INFORMATION to 1.1.1.1:500
Oct 2 06:25:34 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x9995a83b (perhaps this is a duplicated packet)
Oct 2 06:25:34 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: sending encrypted notification INVALID_MESSAGE_ID to 1.1.1.1:500
Oct 2 06:25:36 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0x9995a83b (perhaps this is a duplicated packet)
Oct 2 06:25:36 - [VPN Log]: "user1_rw_rw"[1] 1.1.1.1 #2: sending encrypted notification INVALID_MESSAGE_ID to 1.1.1.1:500
Can anybody help with this?
Thanks in advance.
