I seem to be stuck. I was having ChatGPT help me get the router setup for my network but I seem to have gotten stuck. At one point it decides that we should factory reset then start over. After that it started asking for a username and password. I've tried cisco/cisco and admin/admin both don't work. ChatGPT had me go into rommon to boot without using the user and password but it never works. Any ideas?
rommon 1 > confreg 0x2142
You must reset or power cycle for new config to take effect
rommon 2 > reset
Resetting .......
Rom image verified correctly
System Bootstrap, Version 16.12(1r), RELEASE SOFTWARE
Copyright (c) 1994-2019 by cisco Systems, Inc.
Current image running: Boot ROM1
Last reset cause: LocalSoft
C1111-8P platform with 4194304 Kbytes of main memory
........
no valid BOOT image found
Final autoboot attempt from default boot device...
Located .installer
unable to open bootflash:/.installer (14)
Located throughput_monitor_params
#
Unsupported package header version (-1347440721)
Located c1100-ucmk9.16.10.3a.SPA.bin
################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################ ################################################################################
Package header rev 3 structure detected
IsoSize = 385196032
Calculating SHA-1 hash...Validate package: SHA-1 hash:
calculated ABF4D9CD:AC411F8F:F2CBFF6F:14DFDA32:F57CAD6C
expected ABF4D9CD:AC411F8F:F2CBFF6F:14DFDA32:F57CAD6C
RSA Signed RELEASE Image Signature Verification Successful
Image validated
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software [], ISR Software (ARMV8EB_LINUX_IOSD-UCMK9-M), Version 16.10.
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2019 by Cisco Systems, Inc.
Compiled Tue 17-Sep-19 20:14 by cedge-sw-dev
PLEASE READ THE FOLLOWING TERMS CAREFULLY. INSTALLING THE LICENSE OR
LICENSE KEY PROVIDED FOR ANY CISCO SOFTWARE PRODUCT, PRODUCT FEATURE,
AND/OR SUBSEQUENTLY PROVIDED SOFTWARE FEATURES (COLLECTIVELY, THE
"SOFTWARE"), AND/OR USING SUCH SOFTWARE CONSTITUTES YOUR FULL
ACCEPTANCE OF THE FOLLOWING TERMS. YOU MUST NOT PROCEED FURTHER IF YOU
ARE NOT WILLING TO BE BOUND BY ALL THE TERMS SET FORTH HEREIN.
Your use of the Software is subject to the Cisco End User License Agreement
(EULA) and any relevant supplemental terms (SEULA) found at
http://www.cisco.com/c/en/us/about/legal/cloud-and-software/software-terms.html.
You hereby acknowledge and agree that certain Software and/or features are
licensed for a particular term, that the license to such Software and/or
features is valid only for the applicable term and that such Software and/or
features may be shut down or otherwise terminated by Cisco after expiration
of the applicable license term (e.g., 90-day trial period). Cisco reserves
the right to terminate any such Software feature electronically or by any
other means available. While Cisco may provide alerts, it is your sole
responsibility to monitor your usage of any such term Software feature to
ensure that your systems and networks are prepared for a shutdown of the
Software feature.
cisco C1111-8P (1RU) processor with 1453913K/6147K bytes of memory.
Processor board ID FGL2352LNMN
1 Virtual Ethernet interface
10 Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
4194304K bytes of physical memory.
2945023K bytes of flash memory at bootflash:.
CRYPTO_PKI: setting trustpoint policy TP-self-signed-879729930 to use keypair TP
[OK] (elapsed time was 9 seconds)
Press RETURN to get started!
*Mar 2 23:29:46.516: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module nam
*Mar 2 23:29:47.644: %ISR_THROUGHPUT-6-CRYPTO: Crypto level has been set to 500
*Mar 2 23:29:49.367: %SMART_LIC-6-AGENT_READY: Smart Agent for Licensing is ini
*Mar 2 23:29:55.384: %SPANTREE-5-EXTENDED_SYSID: Extended SysId enabled for typ
failed c3pl_ppcp_trace_write
*Mar 2 23:29:55.821: %VOICE_HA-7-STATUS: CUBE HA-supported platform detected.
*Mar 2 23:29:55.986: ipsec_vesen_init: g_ipsec_vesen_required=TRUE
*Mar 2 23:29:56.528: opendns init: Service Zone bind fail for VPN 65528
*Mar 2 23:29:56.724: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up
*Mar 2 23:29:56.727: %LINK-3-UPDOWN: Interface EOBC0, changed state to up
*Mar 2 23:29:56.728: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0
*Mar 2 23:29:56.732: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0,
*Mar 2 23:29:56.732: %LINK-3-UPDOWN: Interface LIIN0, changed state to up
*Mar 2 23:29:57.709: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
*Mar 2 23:29:57.761: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, ch
*Mar 2 23:29:57.762: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, cha
*Mar 2 23:29:57.762: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, cha
*Mar 2 23:28:19.523: %IOSXE-4-PLATFORM: R0/0: kernel: mvpp2 f2000000.ppv22: Dir
*Mar 2 23:28:44.402: %IOSXE-4-PLATFORM: R0/0: kernel: lfts_sar_purge_thread: Ma
*Mar 2 23:28:59.035: %FLASH_CHECK-3-DISK_QUOTA: R0/0: flash_check: Flash disk q
*Mar 2 23:29:49.498: %CMLIB-3-THROUGHPUT_VALUE_SETUP_FAILED: R0/0: cmand: Throu
*Mar 2 23:29:58.266: %ONEP_BASE-6-SS_ENABLED: ONEP: Service set Base was enable
*Mar 2 23:30:00.312: %SYS-6-STARTUP_CONFIG_IGNORED: System startup configuratio
*Mar 2 23:30:00.323: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/0, interfa
*Mar 2 23:30:00.324: %IOSXE_OIR-6-REMSPA: SPA removed from subslot 0/1, interfa
*Mar 2 23:30:00.343: %SPA_OIR-6-OFFLINECARD: SPA (C1111-2x1GE) offline in subsl
*Mar 2 23:30:00.357: %SPA_OIR-6-OFFLINECARD: SPA (C1111-ES-8) offline in subslo
*Mar 2 23:30:00.362: %IOSXE_OIR-6-INSCARD: Card (fp) inserted in slot F0
*Mar 2 23:30:00.362: %IOSXE_OIR-6-ONLINECARD: Card (fp) online in slot F0
*Mar 2 23:30:00.380: %IOSXE_OIR-6-INSCARD: Card (cc) inserted in slot 0
*Mar 2 23:30:00.380: %IOSXE_OIR-6-ONLINECARD: Card (cc) online in slot 0
*Mar 2 23:30:00.502: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/0
*Mar 2 23:30:00.505: %IOSXE_OIR-6-INSSPA: SPA inserted in subslot 0/1
*Mar 2 23:30:00.568: SDWAN INFO: SDWAN system init done
*Mar 2 23:30:00.701: yang-infra: Auto enable netconf-yang
*Mar 2 23:30:00.702: yang-infra: netconf-yang server has been notified to start
*Mar 2 23:30:01.762: %SYS-5-RESTART: System restarted --
Cisco IOS Software [], ISR Software (ARMV8EB_LINUX_IOSD-UCMK9-M), Version 16.10.
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2019 by Cisco Systems, Inc.
Compiled Tue 17-Sep-19 20:14 by cedge-sw-dev
*Mar 2 23:30:01.910: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 2 23:30:01.915: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Mar 2 23:30:01.814: %IOSXE-4-PLATFORM: R0/0: kernel: LFTS_SAR_rcv_msg: IOSD Re
*Mar 2 23:30:05.821: %SPA_OIR-6-ONLINECARD: SPA (C1111-2x1GE) online in subslot
*Mar 2 23:30:05.898: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL xcvr container 0/0
*Mar 2 23:30:06.234: %SPA_OIR-6-ONLINECARD: SPA (C1111-ES-8) online in subslot
*Mar 2 23:30:06.796: Checking for EXEC mode on console
*Mar 2 23:30:07.691: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/0, changed st
*Mar 2 23:30:07.809: %LINK-3-UPDOWN: Interface GigabitEthernet0/0/1, changed st
*Mar 2 23:30:07.810: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/0
*Mar 2 23:30:08.187: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/0, changed st
*Mar 2 23:30:08.188: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.188: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/1, changed st
*Mar 2 23:30:08.189: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.189: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/2, changed st
*Mar 2 23:30:08.190: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.190: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/3, changed st
*Mar 2 23:30:08.202: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.202: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/4, changed st
*Mar 2 23:30:08.203: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.203: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/5, changed st
*Mar 2 23:30:08.204: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.204: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/6, changed st
*Mar 2 23:30:08.205: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:08.231: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/7, changed st
*Mar 2 23:30:08.232: %IOSXE_RP_ALARM-6-INFO: ASSERT CRITICAL GigabitEthernet0/1
*Mar 2 23:30:10.432: %ONEP_BASE-6-SS_ENABLED: ONEP: Service set Vty was enabled
*Mar 2 23:30:10.883: %ONEP_BASE-6-CONNECT: [Element]: ONEP session Application:
*Mar 2 23:30:11.916: %Cisco-SDWAN-Router-SYSMGR-5-NTCE-200050: R0/0: SYSMGR: Sy
*Mar 2 23:30:11.970: %Cisco-SDWAN-Router-SYSMGR-5-NTCE-200042: R0/0: SYSMGR: Cr
*Mar 2 23:30:11.970: %Cisco-SDWAN-Router-SYSMGR-3-ERRO-200065: R0/0: SYSMGR: Da
*Mar 2 23:30:11.971: %Cisco-SDWAN-Router-SYSMGR-6-INFO-200017: R0/0: SYSMGR: St
*Mar 2 23:30:14.413: %DMI-3-NETCONF_SSH_ERROR: R0/0: ncsshd_bp: NETCONF/SSH: er
*Mar 2 23:30:16.579: %CRYPTO-6-ISAKMP_ON_OFF: ISAKMP is OFF
*Mar 2 23:30:16.579: %CRYPTO-6-GDOI_ON_OFF: GDOI is OFF
*Mar 2 23:30:17.109: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named CISCO_IDEVID_SU
*Mar 2 23:30:17.463: %PKI-2-NON_AUTHORITATIVE_CLOCK: PKI functions can not be i
*Mar 2 23:30:23.407: %LINK-3-UPDOWN: Interface GigabitEthernet0/1/0, changed st
*Mar 2 23:30:23.410: %IOSXE_RP_ALARM-6-INFO: CLEAR CRITICAL GigabitEthernet0/1/
*Mar 2 23:30:24.446: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
*Mar 2 23:30:24.470: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
*Mar 2 23:30:26.315: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-
*Mar 2 23:30:26.417: %SSH-5-ENABLED: SSH 1.99 has been enabled
*Mar 2 23:30:33.646: %CRYPTO_ENGINE-5-KEY_ADDITION: A key named TP-self-signed-
*Mar 2 23:31:36.088: %DMI-5-ACTIVE: R0/0: nesd: process is in steady state.
*Mar 2 23:31:36.088: %Cisco-SDWAN-Router-SYSMGR-5-NTCE-200050: R0/0: SYSMGR: Sy
*Mar 2 23:31:36.800: EXEC mode enabled on console
*Mar 2 23:31:38.675: %LINK-3-UPDOWN: Interface Vlan1, changed state to down
*Mar 2 23:31:39.677: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
*Mar 2 23:31:40.954: %INSTALL-5-OPERATION_START_INFO: R0/0: packtool: Started e
*Mar 2 23:31:51.816: %PNP-6-PNP_DISCOVERY_STOPPED: PnP Discovery stopped (Start
*Mar 2 23:32:08.673: %LINK-3-UPDOWN: Interface Vlan1, changed state to up
*Mar 2 23:32:09.674: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan1, cha
*Mar 2 23:32:30.308: %INSTALL-5-OPERATION_COMPLETED_INFO: R0/0: packtool: Compl
*Mar 2 23:32:42.431: %INSTALL-5-INSTALL_START_INFO: R0/0: install_engine: Start
*Mar 2 23:32:43.337: %INSTALL-5-INSTALL_COMPLETED_INFO: R0/0: install_engine: C
User Access Verification
Username: admin
Password:
% Authentication failed
Username: cisco
Password:
% Authentication failed
