cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2431
Views
0
Helpful
4
Replies

1921 Router PPPoe issue

steve.robinson
Level 1
Level 1

I have setup a 1921 Cisco router to connect to and ISP to provide Guest Wifi and I am in the early stages of setting it up. the config is below but from a client PC plugged in gi0/1 I can ping 216.589.214.35 but when I open IE it won't connect.

I can also ping everything from the router except the client PC 192.168.0.11 which is supplied via DHCP from the router

version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname TEST
!
boot-start-marker
boot-end-marker
!
!
!
no aaa new-model
!
no ipv6 cef
ip source-route
ip cef
!
!
!
ip dhcp excluded-address 192.168.0.1 192.168.0.10
!
ip dhcp pool DHCP_GUEST
 import all
 network 192.168.0.0 255.255.255.0
 default-router 192.168.0.1
!
!
multilink bundle-name authenticated
!
password encryption aes
crypto pki token default removal timeout 0
!
!
!
!
username admin privilege 15 secret 5
!
!
interface Embedded-Service-Engine0/0
 no ip address
 shutdown
!
interface GigabitEthernet0/0
 description Link_to_ZEN
 no ip address
 duplex auto
 speed auto
 pppoe enable group global
 pppoe-client dial-pool-number 1
 no mop enabled
!
interface GigabitEthernet0/1
 ip address 192.168.0.1 255.255.255.0
 ip nat inside
 no ip virtual-reassembly in
 ip tcp adjust-mss 1452
 duplex auto
 speed auto
!
interface Serial0/0/0
 no ip address
 shutdown
 clock rate 2000000
!
interface Dialer1
 mtu 1492
 ip address negotiated
 ip nat outside
 ip virtual-reassembly in
 encapsulation ppp
 dialer pool 1
 dialer-group 1
 ppp authentication pap callin
 ppp chap hostname xxxxxxx
 ppp chap password 0 xxxxxxx
 ppp pap sent-username xxxxxxx password 0 xxxxxxx
!
ip forward-protocol nd
!
no ip http server
no ip http secure-server
!
ip nat inside source list 10 interface Dialer1 overload
ip nat inside source list DSL_ACCESSLIST interface Dialer1 overload
ip route 0.0.0.0 0.0.0.0 Dialer1
!
ip access-list extended DSL_ACCESSLIST
 permit ip any any
!
access-list 10 permit 192.168.0.0 0.0.0.255
!
!
control-plane
!
!
line con 0
 login local
line aux 0
line 2
line vty 0 4
 login local
 transport input ssh
!
scheduler allocate 20000 1000
end

Also the out put from "sh ip route" and "sh ip int bri"

----------------------------------------------------------------------------------------------------

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP
       D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
       N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
       E1 - OSPF external type 1, E2 - OSPF external type 2
       i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2
       ia - IS-IS inter area, * - candidate default, U - per-user static route
       o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP
       + - replicated route, % - next hop override

Gateway of last resort is 0.0.0.0 to network 0.0.0.0

S*    0.0.0.0/0 is directly connected, Dialer1
      62.0.0.0/32 is subnetted, 1 subnets
C        62.3.80.17 is directly connected, Dialer1
      88.0.0.0/32 is subnetted, 1 subnets
C        88.97.23.187 is directly connected, Dialer1
      192.168.0.0/24 is variably subnetted, 2 subnets, 2 masks
C        192.168.0.0/24 is directly connected, GigabitEthernet0/1
L        192.168.0.1/32 is directly connected, GigabitEthernet0/1

--------------------------------------------------------------------------------------------------------------------

Any interface listed with OK? value "NO" does not have a valid configuration

Interface                  IP-Address      OK? Method Status                Protocol
Embedded-Service-Engine0/0 unassigned      YES unset  administratively down down
GigabitEthernet0/0         unassigned      YES unset  up                    up
GigabitEthernet0/1         192.168.0.1     YES manual up                    up
Serial0/0/0                unassigned      YES unset  administratively down down
Dialer1                    88.97.23.187    YES IPCP   up                    up
NVI0                       unassigned      NO  unset  up                    up
Virtual-Access1            unassigned      YES unset  up                    up
Virtual-Access2            unassigned      YES unset  up                    up

-------------------------------------------------------------------------------------------------------------------

1 Accepted Solution

Accepted Solutions

Hello,

could be just a DNS problem. Try and add the Google DNS servers to your DHCP pool:

ip dhcp pool DHCP_GUEST
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1

dns-server 8.8.8.8 8.8.4.4

View solution in original post

4 Replies 4

Hello,

try and add:

dialer-list 1 protocol ip permit

to the configuration.

Hi

I added dialer-list 1 protocol ip permit but the client still fails to open a web page from IE but yet can still ping 216.58.214.35, I have tried another PC and that to has the same issue.

Hello,

could be just a DNS problem. Try and add the Google DNS servers to your DHCP pool:

ip dhcp pool DHCP_GUEST
import all
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1

dns-server 8.8.8.8 8.8.4.4

steve.robinson
Level 1
Level 1

I had just thought of the very same thing, and once added the DNS servers everything worked, Thanks.

Review Cisco Networking for a $25 gift card