please i need urgent solution to the log below.i need to access the switch.ports not blinking at all but fan on.what do i do
C2950 Boot Loader (C2950-HBOOT-M) Version 12.1(11r)EA1, RELEASE SOFTWARE (fc1)
Compiled Mon 22-Jul-02 17:18 by antonino
WS-C2950-24 starting...
Base ethernet MAC Address: 00:17:5a:1c:77:40
Xmodem file system is available.
Initializing Flash...
flashfs[0]: 373 files, 4 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 7741440
flashfs[0]: Bytes used: 4752384
flashfs[0]: Bytes available: 2989056
flashfs[0]: flashfs fsck took 7 seconds.
...done initializing flash.
Boot Sector Filesystem (bs:) installed, fsid: 3
Parameter Block Filesystem (pb:) installed, fsid: 4
Loading "flash:/c2950-i6q4l2-mz.121-22.EA6.bin"...#############################################################################################################################################################################################################
File "flash:/c2950-i6q4l2-mz.121-22.EA6.bin" uncompressed and installed, entry point: 0x80010000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6Q4L2-M), Version 12.1(22)EA6, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Fri 21-Oct-05 01:59 by yenanh
Image text-base: 0x80010000, data-base: 0x80568000
Initializing flashfs...
flashfs[1]: 373 files, 4 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 7741440
flashfs[1]: Bytes used: 4752384
flashfs[1]: Bytes available: 2989056
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
Done initializing flashfs.
POST: System Board Test : Passed
POST: Ethernet Controller Test : Passed
ASIC Initialization Passed
%Error: initializing transceiver port Fa0/1
%Error: initializing transceiver port Fa0/2
%Error: initializing transceiver port Fa0/3
%Error: initializing transceiver port Fa0/4
%Error: initializing transceiver port Fa0/5
%Error: initializing transceiver port Fa0/6
%Error: initializing transceiver port Fa0/7
%Error: initializing transceiver port Fa0/8
%Error: initializing transceiver port Fa0/9
%Error: initializing transceiver port Fa0/10
%Error: initializing transceiver port Fa0/11
%Error: initializing transceiver port Fa0/12
%Error: initializing transceiver port Fa0/13
%Error: initializing transceiver port Fa0/14
%Error: initializing transceiver port Fa0/15
%Error: initializing transceiver port Fa0/16
%Error: initializing transceiver port Fa0/17
%Error: initializing transceiver port Fa0/18
%Error: initializing transceiver port Fa0/19
%Error: initializing transceiver port Fa0/20
%Error: initializing transceiver port Fa0/21
%Error: initializing transceiver port Fa0/22
%Error: initializing transceiver port Fa0/23
%Error: initializing transceiver port Fa0/24
