cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
5386
Views
0
Helpful
23
Replies

876W Router: internet wired but no wireless internet, need help configuring

EH1165305
Level 1
Level 1

For a long time now I try to get my 876 Wireless Router configured but I do not succeed. (I'm just a cisco loving amateur so please respect my poor knowledge)

Problem is that I got the router setup for internet connection but only wired. Now I have a configuration in which I also succeed to make a wireless connection. Only the problem is that the wireless connection does not get to the internet.

Next to some other minor looking problems that will be the main thing!

I tried several helpfull tools as CCP and some sites which gave a Form-template on the internet or a Excel-sheet to fill in. All those did not function for me.

Now I hope there will be someone out there who is willing to have a look at my running-config and give me a helping hand.

Thanks in advance,

Emil

Building configuration...

Current configuration : 6294 bytes

!

! Last configuration change at 03:55:22 UTC Thu Apr 29 2010 by Router876W

!

version 15.0

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname yourname

!

boot-start-marker

boot-end-marker

!

logging buffered 51200 warnings

!

no aaa new-model

!

!

!

crypto pki trustpoint TP-self-signed-1959697149

enrollment selfsigned

subject-name cn=IOS-Self-Signed-Certificate-1959697149

revocation-check none

rsakeypair TP-self-signed-1959697149

!

!

crypto pki certificate chain TP-self-signed-1959697149

certificate self-signed 01

<KEY-FOLLOWS-HERE>


   quit

dot11 syslog

!

dot11 ssid 876W

vlan 1

authentication open

authentication key-management wpa

wpa-psk ascii 0 <MYKEY>

!

ip source-route

!

!

ip dhcp excluded-address 10.10.10.1

!

ip dhcp pool ccp-pool

   import all

   network 10.10.10.0 255.255.255.248

   default-router 10.10.10.1

   lease 0 2

!

!

ip cef

no ip domain lookup

ip domain name yourdomain.com

no ipv6 cef

!

multilink bundle-name authenticated

!

!

!

username Router876W privilege 15 secret 5 <MYSECRET>

!

!

!

interface BRI0

no ip address

encapsulation hdlc

shutdown

!

!

interface ATM0

no ip address

no atm ilmi-keepalive

!

!

interface ATM0.1 point-to-point

pvc 8/48

  encapsulation aal5mux ppp dialer

  dialer pool-member 1

!

!

interface FastEthernet0

!

!

interface FastEthernet1

!

!

interface FastEthernet2

!

!

interface FastEthernet3

!

!

interface Dot11Radio0

no ip address

!

encryption vlan 1 mode ciphers aes-ccm tkip

!

broadcast-key vlan 1 change 30

!

!

ssid 876W

!

mbssid

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0

station-role root

!

!

interface Dot11Radio0.1

encapsulation dot1Q 1 native

no cdp enable

bridge-group 1

bridge-group 1 subscriber-loop-control

bridge-group 1 spanning-disabled

bridge-group 1 block-unknown-source

no bridge-group 1 source-learning

no bridge-group 1 unicast-flooding

!

interface Vlan1

description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$

ip address 10.10.10.1 255.255.255.0

ip nat inside

ip virtual-reassembly

ip tcp adjust-mss 1452

!

!

interface Dialer0

ip address <MY-ISPGIVEN-FIX-IPADDRESS> 255.255.255.0

ip nat outside

ip virtual-reassembly

encapsulation ppp

dialer pool 1

dialer-group 1

ppp authentication pap callin

ppp pap sent-username <MYUSERNAME> password 0 <MYPASS>

no cdp enable

!

!

ip forward-protocol nd

ip http server

ip http access-class 23

ip http authentication local

ip http secure-server

ip http timeout-policy idle 60 life 86400 requests 10000

!

!

ip nat inside source list 1 interface Dialer0 overload

ip route 0.0.0.0 0.0.0.0 Dialer0

!

access-list 1 remark INSIDE_IF=Vlan1

access-list 1 remark CCP_ACL Category=2

access-list 1 permit 10.10.10.0 0.0.0.7

access-list 23 permit 10.10.10.0 0.0.0.7

dialer-list 1 protocol ip permit

no cdp run

!

control-plane

!

line con 0

login local

no modem enable

line aux 0

line vty 0 4

access-class 23 in

privilege level 15

login local

transport input telnet ssh

!

scheduler max-task-time 5000

end

23 Replies 23

Thanks. Wireless is now working. I have a connection with internet on my connected Iphone.

Strange enough though now wired internet is not working anymore

On the connected console I can ping my DNS from within the console-connection. Also get a addressresolution for www.google.nl. I can ping my Iphone. I can not ping my ISP IP adress though!

On my wired laptop the internet browser does not find google or other addresses. In the dos prompt I can not ping to my own ISP address, no DNS.

What I did was as you suggested bridge 1 route ip and removed "ip tcp adjust-mss 1452" from vlan 1.

Some suggestions left... Would make me very happy

Yep...try:

bridge 1 protocol ieee

See if that gets your wired side working, and you should be good....

John

HTH, John *** Please rate all useful posts ***

Thanks for your very fast responding as I'm in the middle of the night and have to get up in a few hours. But this is important for me and I hope to solve it with your help.

Unfortunately nothing changed!

I can ping my Iphone yes. But still no internet from the wired connected laptop. I did not see a change after bridge 1 protocol ieee command....

Hmmm.....are you getting an address on the wired side? Can you ping the router at 10.10.10.1?

Also, what port are you connected to? Are you connected to the switch on the router or another switch that's connected to the router? What port is that connected to on the router?

HTH, John *** Please rate all useful posts ***

Sorry about taking so long. Have to plug and unplug on my two routers for connection to you.

I cannot ping out of the laptop to the router. Which I could before I got it wireless.

Tried F0 and after that also F4. Both don't give ping possible.

I have a switch, but for this "exercise" I made the connections directly to the router. The switch is not connected now. The IP address I gave the laptop is 10.10.10.4 and should be ok with DNS, gateway and mask set.

I don't know if it is of interest but I did a sh ip int brief and saw that the BVI1 is not up so I did a manual no shut.

This unfortunately did not solve the problem either and I hope I did not disturb your thinking about the solution.

Here is the output:

yourname#sh ip int brief
Interface                  IP-Address      OK? Method Status                Protocol
ATM0                       unassigned      YES NVRAM  up                    up
ATM0.1                     unassigned      YES unset  up                    up
BRI0                       unassigned      YES NVRAM  administratively down down
BRI0:1                     unassigned      YES unset  administratively down down
BRI0:2                     unassigned      YES unset  administratively down down
BVI1                       10.10.10.1      YES manual up                    up
Dialer0                    213.xx.xx.xx   YES NVRAM  up                    up
Dot11Radio0                unassigned      YES NVRAM  up                    up
Dot11Radio0.1              unassigned      YES unset  up                    up
FastEthernet0              unassigned      YES unset  up                    up
FastEthernet1              unassigned      YES unset  up                    down
FastEthernet2              unassigned      YES unset  up                    down
FastEthernet3              unassigned      YES unset  up                    down
NVI0                       unassigned      YES unset  administratively down down
Virtual-Access1            unassigned      YES unset  up                    up
Virtual-Access2            unassigned      YES unset  up                    up
Vlan1                      unassigned      YES manual up                    down

And my intervention to get the BVI1 up

yourname(config)#int BVI1
yourname(config-if)#no shut
yourname(config-if)#exit
yourname(config)#exit

See now that is was up but what is down is the BVI1. Don't know if this is important and how to solve....

Sorry. I replied to you yesterday from my phone by replying to the email, but it didn't post apparently.

On the port that you're connected to in the router, change that port to a trunk port. I'm not sure if that will do anything, but that's the only difference between yours and my 871W that I have configured. So, if you're connected to FA0, try:

int fa0

switch mode trunk

Let me know if this did anything. Also, after you do that, if you haven't rebooted you may want to try that as well.

HTH,

John

HTH, John *** Please rate all useful posts ***

Thanks John you did not give up. I went to bed and did not get any messages anymore. So I thought that was it. Problem cannot be solved. Maybe a hardware issue, although strange.

But... you made my day.

After I gave the swithport command, which I will try to undo also later on this day as I have no time at the moment, nothing changed.

Than I did the copy run start and rebootet.

And thanks God I'm online now with the 876W router wired to my laptop! And also my Iphone is still working wireless connected.

You cannot imagine how glad I am

Now I don't know what went wrong and if I should have rebooted earlier on the problem would be solved before the last issues, where you where stonnishing about not functioning after your great help. But anyhow it functions wireless and wired to at the moment.

Later on in the weekend I have some more time and will have a look if I can get my Cisco switch again inbetween as the rest of my computers now is ofline.

Again thank you very much for your great consistent and appreciated help. You earn a goldmedail!

Emil

Message was edited by: Emil Heilbron I did a no switch trunk and now the switch is inbetween again. Maybe I can ask you a last question as I detected that my other computers are not in the range of IP addresses. How can I make some more IP addresses connect to the router? Thanks

Glad to hear it   Sometimes a reboot is all that's needed, especially when nothing else makes sense! LOL! If you would, please rate this post so others can find it if needed.....

Thanks!

John

HTH, John *** Please rate all useful posts ***

I rearanged the access-list 1. After your lessons I forgot everything

Thanks again.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: