a alarm about 7600 SIP200

[flyipmm914]

SLOT 1: Nov  9 02:24:36.595: %C7600_SIP200_SPIRX-3-SPA_INTERRUPT: SPA 0 -  seq err,  SPA Int status = 0x4

SLOT 1: Nov  9 02:24:36.595: %C7600_SIP200_SPIRX-3-SPI4_LINKERROR: SPA Bay 0,  1 SPI4 Link Failures

Configuration details of POS1/0/1::

MTU: 4470, xmit_delay: 0, CRC: crc32, Framing: sdh, Clock source: internal

Scramble: off, ais_shut: off, tx_j0: 0x1

aps_working: off, aps_protect: off, aps_signalling; SDH MSP

Vector Details:

fastsend            = 0x4025798C, turbofs    = 0x403E1918

multicast fs        = 0x403E1918, tagfs      = 0x00000000

tag optimum fs      = 0x405A67E0, ip2tagfs   = 0x00000000

ip2tag optimum fs   = 0x00000000, ipv62tagfs = 0x00000000

Counters:

Rx Bytes = 145341413880, Tx Bytes = 214696843076

Rx Pkts  = 893943008, Tx Pkts  = 1026362687

Rx CRC Errs = 66291505, Tx Underruns = 0

Rx Giants = 60754, Tx Aborts = 0

Rx Ignore = 0

Rx Runts = 5795603

Rx Aborts= 222904

I think maybe line probelm case this alarm,because there was too may rants.

try to find answer on cisco.com，but failed。what about you opinion？ thanks。

[Bert Gevers]

Hi Ying,

what software version are you running on the 7600?

I believe you may be encountering:
CSCsm80678    SIP-200 logs "%SIP200_SPIRX-3-SPA_INTERRUPT" error message continuously
Externally found minor (Sev4) bug: D-Duplicate

which is fixed through:

CSCsq19146    FPD creation for new pegasus rx (1.6) FPA image for Sip-1 CR
Externally found severe (Sev2) bug: V-Verified

This defect is seen when there is a series of runts received on the card.

I would recommend to upgrade the FTP and IOS on the device to a version which incorporates CSCsq19146.

FPD upgrade instructions can be found here:

http://cisco.biz/en/US/docs/interfaces_modules/shared_port_adapters/configuration/7600series/76fpd.html

Afterwards, verify if the runts are still present as they may be caused by a line problem indeed.

HTH,

Bert

[flyipmm914]

------------------ show version ------------------

Cisco Internetwork Operating System Software

IOS (tm) cwlc Software (sip1-DW-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Thu 23-Mar-06 20:09 by tinhuang

Image text-base: 0x40011050, data-base: 0x40700000

ROM: System Bootstrap, Version 12.2(20051006:192046) [rwoods-pikespeak 125], DEVELOPMENT SOFTWARE

ROM: cwlc Software (sip1-DW-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)

SIP-200-1 uptime is 1 year, 29 weeks, 8 hours, 48 minutes

System returned to ROM by power-on

System restarted at 17:39:44 UTC Sun Apr 19 2009

Running default software

cisco CWAN Sibyte Interface Processor (SB-1) processor (revision 0xFF) with 393216K/131071K bytes of memory.

SB-1 CPU at 800Mhz, Implementation 0x401, Rev 0.2, 512KB L2 Cache

Last reset from power-on

1 FastEthernet/IEEE 802.3 interface

2 Packet over SONET network interfaces

Configuration register is 0x4 (will be 0x0 at next reload)

I have saw that documentation ,thank you very much!