We recently purchased a C819G-4G-V-K9 for a remote site that has no ISP available. I can't seem to get this working properly. I can tell the cell portion is up and working becuase I can send the router a text message and I receive it on the router. The cell 0 interface however, is not getting a dhcp address. Below is my configuration:
hostname Router
!
boot-start-marker
boot system flash:c800-universalk9-mz.SPA.153-3.M.bin
boot-end-marker
!
aqm-register-fnf
!
no aaa new-model
memory-size iomem 10
!
ip cef
no ipv6 cef
!
multilink bundle-name authenticated
!
chat-script lte "" "AT!CALL1" TIMEOUT 60 "OK"
!
license udi pid C819G-4G-V-K9 sn FTX180680R8
!
!
vtp domain MobileCell
vtp mode transparent
!
controller Cellular 0
!
interface Cellular0
ip address negotiated previous
ip nat outside
ip virtual-reassembly in
encapsulation slip
dialer in-band
dialer string lte
dialer-group 1
async mode interactive
!
interface FastEthernet0
no ip address
!
interface FastEthernet1
no ip address
!
interface FastEthernet2
no ip address
!
interface FastEthernet3
no ip address
!
interface GigabitEthernet0
no ip address
shutdown
duplex auto
speed auto
!
interface Serial0
no ip address
shutdown
clock rate 2000000
!
interface Vlan1
ip address 192.168.0.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
!
ip forward-protocol nd
no ip http server
no ip http secure-server
!
!
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
!
dialer-list 1 protocol ip list 1
!
access-list 1 permit any
!
control-plane
!
!
!
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
!
mgcp profile default
!
!
line con 0
script dialer lte
no modem enable
line aux 0
script dialer lte
modem InOut
no exec
line 2
no activation-character
no exec
transport preferred none
transport input all
stopbits 1
line 3
script dialer lte
modem InOut
no exec
line vty 0 4
login
transport input all
!
scheduler allocate 20000 1000
!
end
Cellular0 is up (spoofing), line protocol is up (spoofing)
Hardware is 4G WWAN Modem - Verizon Multimode LTE/eHRPD/EVDO RevA/Rev0/1xRTT
Internet address will be assigned dynamically by the network
MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation SLIP, loopback not set
Keepalive not supported
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/10 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=down DSR=down DTR=up RTS=up CTS=up
Router#sh ip int bri
Interface IP-Address OK? Method Status Protocol
Cellular0 unassigned YES manual up up
FastEthernet0 unassigned YES unset down down
