cisco 4500 -standby supervisor is disabled state?

hasan yenilmez · ‎01-02-2013

Hi ,

what can be the reason , standby supervisor is disabled state ?

redundancy mode sso, show redundancy and show module outoputs are below.

thanks in advance

4510R-E#show redundancy states

my state = 13 -ACTIVE

peer state = 1 -DISABLED

Mode = Simplex

Unit = Primary

Unit ID = 5

Redundancy Mode (Operational) = Stateful Switchover

Redundancy Mode (Configured) = Stateful Switchover

Redundancy State = Non Redundant

Maintenance Mode = Disabled

Manual Swact = disabled (system is simplex (no peer unit))

Communications = Down Reason: Simplex mode

client count = 54

client_notification_TMR = 240000 milliseconds

keep_alive TMR = 9000 milliseconds

keep_alive count = 0

keep_alive threshold = 18

RF debug mask = 0x0

-----------

4510R-E#show module

Chassis Type : WS-C4510R-E

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 24 1000BaseX (SFP) WS-X4624-SFP-E JAE14080M09

2 24 1000BaseX (SFP) WS-X4624-SFP-E JAE14080LZ7

3 18 10GE (X2), 1000BaseX (SFP) WS-X4606-X2-E JAE140901X6

4 18 10GE (X2), 1000BaseX (SFP) WS-X4606-X2-E JAE140901QN

5 6 Sup 6-E 10GE (X2), 1000BaseX (SFP) WS-X45-SUP6-E JAE141205MH

6 Supervisor

7 18 10GE (X2), 1000BaseX (SFP) WS-X4606-X2-E JAE140901QS

8 48 1000BaseX SFP WS-X4448-GB-SFP JAE1406496U

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 0026.99ad.f1f8 to 0026.99ad.f20f 1.1 Ok

2 0026.99ad.f9e4 to 0026.99ad.f9fb 1.1 Ok

3 0026.99ad.f582 to 0026.99ad.f593 1.2 Ok

4 0026.99ad.f67e to 0026.99ad.f68f 1.2 Ok

5 68ef.bdab.7c80 to 68ef.bdab.7c85 1.6 12.2(44r)SG5 12.2(53)SG1 Ok

6 Unknown Unknown Unknown Other

7 0026.99ad.f6b4 to 0026.99ad.f6c5 1.2 Ok

8 68ef.bd15.5da0 to 68ef.bd15.5dcf 1.3 Ok

Mod Redundancy role Operating mode Redundancy status

----+-------------------+-------------------+----------------------------------

5 Active Supervisor SSO Active

6 Standby Supervisor SSO Disabled

mahmoodmkl · ‎01-02-2013

Hi

I think u need to install the SUP's in slot 1 and 2.

Thanks

Ivan Shirshin · ‎01-07-2013

Hi,

No, slots 5 and 6 are reserved for sup on 4510R.

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

Ivan Shirshin · ‎01-07-2013

Hi,

It is likely standby sup is stuck in boot or ROMMON mode as it is showing Other status in the outputs above.

Connect with console to it and check which state it is in. If it is in ROMMON, try boot with manual "boot" command.

By the way, did you check if the 12.2(53)SG1 image present in the specified boot location on standby?

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.

Kind Regards,
Ivan

SatyenKarande · ‎07-17-2019

@Ivan Shirshin wrote:
Hi,

It is likely standby sup is stuck in boot or ROMMON mode as it is showing Other status in the outputs above.
Connect with console to it and check which state it is in. If it is in ROMMON, try boot with manual "boot" command.
@Ivan Shirshin wrote:
Hi,

It is likely standby sup is stuck in boot or ROMMON mode as it is showing Other status in the outputs above.
Connect with console to it and check which state it is in. If it is in ROMMON, try boot with manual "boot" command.

By the way, did you check if the 12.2(53)SG1 image present in the specified boot location on standby?

Kind Regards,
Ivan Shirshin

**Please grade this post if you find it useful.
Hi Ivan,
If we boot the secondary SUP from the ROMMON mode, will only this SUP be booted or the entire switch will reboot?

Thanks and Regards

Satyen

**Please grade this post if you find it useful.

MASCisco16 · ‎01-01-2020

Thank you. It was in ROMMON mode and boot command resolved the issue.

plinkqld · ‎12-11-2013

My sup is getting to the loading ios services and then nothing. problem is happenning with two sup 7's, one original and one added from spares...

shiguoshun · ‎04-01-2016

Hello,I have this question withe the same of your !

IS this problem is OK?

And how you to do it well?Would you tell me ?

Thans a lot !

suz-b2-1f-cat07#show module

Chassis Type : WS-C4510R+E

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 48 10/100/1000BaseT UPOE E Series WS-X4748-UPOE+E CAT1924L9T4

2 48 10/100/1000BaseT UPOE E Series WS-X4748-UPOE+E CAT1924L9XY

3 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E CAT1951L0P0

4 48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E CAT1950L70J

5 Supervisor

6 8 Sup 8-E 10GE (SFP+), 1000BaseX (SFP) WS-X45-SUP8-E CAT1944L34H

7 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE102863S1

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 d8b1.9027.58e4 to d8b1.9027.5913 1.1 Ok

2 80e0.1d5a.560c to 80e0.1d5a.563b 1.1 Ok

3 00f2.8b0f.4e78 to 00f2.8b0f.4ea7 1.1 Ok

4 cc46.d611.c6f0 to cc46.d611.c71f 1.1 Ok

5 Unknown Unknown Unknown Other

6 58ac.78b4.b408 to 58ac.78b4.b40f 1.3 15.1(1r)SG5 03.03.00.XO Ok

7 0018.73bb.1880 to 0018.73bb.18af 2.3 Ok

Mod Redundancy role Operating mode Redundancy status

----+-------------------+-------------------+----------------------------------

5 Standby Supervisor RPR Disabled

6 Active Supervisor RPR Active

samdoherty10 · ‎08-03-2016

Hi, I have the same issue - was this resolved?

shiguoshun · ‎08-03-2016

HI,I thinka you must upgrade the SUP's IOS,make sure is the same with the first one .you can add my QQ:26296016.