02-12-2012 03:53 PM - edited 03-04-2019 03:14 PM
Hey Guys,
I'm trying to use a Sup6-E to do some intelligent shaping. I'm getting an error and I think its because of the architecture of the 4500 QoS. Most likely this type of QoS is not supported so I was wondering if anyone had any ideas on how to implement this QoS policy.
This is what I want to accomplish
!
class-map match-any PRIORITY-QUEUE
match dscp ef
match dscp cs5
match dscp cs4
!
class-map match-any CONTROL-MGMT-QUEUE
match dscp cs7
match dscp cs6
match dscp cs3
match dscp cs2
!
class-map match-any NETWORK-CRITICAL
match dscp cs6
match dscp cs2
!
class-map match-any MULTIMEDIA-CONFERENCING-QUEUE
match dscp af41 af42 af43
!
class-map match-any MULTIMEDIA-STREAMING-QUEUE
match dscp af31 af32 af33
!
class-map match-any TRANSACTIONAL-DATA-QUEUE
match dscp af21 af22 af23
!
class-map match-any BULK-DATA-QUEUE
match dscp af11 af12 af13
!
class-map match-any SCAVENGER-QUEUE
match dscp cs1
!
!
policy-map 1P7Q1T
class PRIORITY-QUEUE
priority
class CONTROL-MGMT-QUEUE
bandwidth remaining percent 10
class MULTIMEDIA-CONFERENCING-QUEUE
bandwidth remaining percent 10
class MULTIMEDIA-STREAMING-QUEUE
bandwidth remaining percent 10
class TRANSACTIONAL-DATA-QUEUE
bandwidth remaining percent 10
dbl
class BULK-DATA-QUEUE
bandwidth remaining percent 4
dbl
class SCAVENGER-QUEUE
bandwidth remaining percent 1
class class-default
bandwidth remaining percent 25
dbl
!
!
!
ip access-list extended ACL-SITE1
permit ip any 172.16.1.0 0.0.0.255
!
ip access-list extended ACl-SITE2
permit ip any 172.17.1.0 0.0.0.255
!
!
class-map match-all CLASS-SITE1
match access-group name ACL-SITE1
!
class-map match-all CLASS-SITE2
match access-group name ACL-SITE2
!
!
When I create my Parent/Child Policy-map I get an error. Is there any way i can meet the objective which is, match the ACLs, shape their bandwidth to 10Mbps and within their shaped 10Mbps bandwidth, allocate specific bandwidth percentages for the traffic matching Dscp values?
!
policy-map POLICY-WAN-SHAPER
class NETWORK-CRITICAL
bandwidth remaining percent 1
class CLASS-ACL1
shape average 10000000
service-policy 1P7Q1T
class CLASS-ACL2
shape average 10000000
service-policy 1P7Q1T
I get the following error when I try to apply the nested service-policy.
%Queuing actions can be at only one of the policy-maps in a hierarchical policy-map. Configuration failed!
Then apply to Sup6-E interface.
!
policy-map POLICY-WAN
class class-default
shape average 100000000
service-policy POLICY-WAN-SHAPER
!
interface ten1/1
service-policy output POLICY-WAN
I know this can be done on the ASR and obviously this is not an ASR router but I'm trying to get this scenario fullfilled. Is it possible?
02-12-2012 08:04 PM
The C4500 is not a WAN router, hense, it will not support HQoS.
This is the same story in the C6K LAN line card. But the good part is, the C6K has SIP/SPA to support WAN connectivity and features.
HTH,
jerry
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide