05-08-2005 03:38 AM - edited 03-03-2019 09:30 AM
The particular error in question that was showing in the log of the 6509 for example:
May 4 16:58:25: %PM_SCP-SP-6-LCP_FW_ERR_INFORM: Module 6 is experiencing the following error: LTL Parity error detected on Coil #0.
May 4 16:58:25: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet6/5, changed state to down
May 4 16:58:25: %PM-SP-4-ERR_DISABLE: packet-buffer error detected on Fa6/5, putting Fa6/5 in err-disable state
Any one run across this and have any suggestions on this one? I understand that the port went into a errdisable, but as for the error in question why did this occur?
Here is the module info...
Switch>sh mod 6
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
6 24 24 port 100FX Multi mode WS-X6324-100FX-MM SAD050313UF
Mod MAC addresses Hw Fw Sw Status
--- ---------------------------------- ------ ------------ ------------ -------
6 0002.fc24.fd40 to 0002.fc24.fd57 1.2 5.4(2) 8.3(0.111)TF Ok
Mod Online Diag Status
--- -------------------
6 Pass
05-09-2005 09:17 PM
bump...
anyone?
05-09-2005 09:29 PM
Hi
I have got the same message. Couldn't find out the problem yet.
The local cisco engineet says this might have caused because of an external problem.
2005 Mar 14 18:37:34 %SYS-4-SYS_LCPERR4:Module 3: LTL Parity error detected on Coil #1.:
Module requires attention - troubleshoot or contact TAC for
2005 Mar 14 18:37:34 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/13.
2005 Mar 14 18:37:34 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/14.
2005 Mar 14 18:37:34 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/15.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/16.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/17.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/18.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/19.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/20.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/21.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/22.
2005 Mar 14 18:37:35 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/23.
2005 Mar 14 18:37:36 %SYS-3-PKTBUFFERFAIL_ERRDIS:Packet buffer failure detected. Err-disabling port 3/24.
****************** show module ******************
Mod Slot Ports Module-Type Model Sub Status
--- ---- ----- ------------------------- ------------------- --- --------
1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok
15 1 1 Multilayer Switch Feature WS-F6K-MSFC2 no ok
2 2 16 1000BaseX Ethernet WS-X6416-GBIC no ok
3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
4 4 16 1000BaseX Ethernet WS-X6516A-GBIC no ok
Mod Module-Name Serial-Num
--- -------------------- -----------
1 SAD05020RBC
15 SAD05020UH5
2 SAD042406GD
3 SAD04260MDS
4 SAL0809V3LP
Mod MAC-Address(es) Hw Fw Sw
--- -------------------------------------- ------ ---------- -----------------
1 00-02-7e-27-02-42 to 00-02-7e-27-02-43 7.4 5.3(2) 7.6(5)
00-02-7e-27-02-40 to 00-02-7e-27-02-41
00-03-e4-67-f8-00 to 00-03-e4-67-fb-ff
15 00-04-dd-56-16-80 to 00-04-dd-56-16-bf 1.7 12.1(13)E2 12.1(13)E2
2 00-30-b6-3f-37-30 to 00-30-b6-3f-37-3f 1.1 5.3(1) 7.6(5)
3 00-01-97-50-5d-c0 to 00-01-97-50-5d-ef 1.1 5.3(1) 7.6(5)
4 00-0f-34-3a-cc-70 to 00-0f-34-3a-cc-7f 3.0 7.2(1) 7.6(5)
Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw
--- ----------------------- ------------------- ----------- ------ ------
1 L3 Switching Engine WS-F6K-PFC SAD05020P8J 1.1
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide