Thank you Giuseppe,
here you are!
show controller atm
###########################################################
Interface ATM2/0 is up
Hardware is ENHANCED ATM PA - OC3 (155000Kbps)
Framer is PMC PM5346 S/UNI-155-LITE, SAR is LSI ATMIZER II
Firmware rev: G161, Framer rev: 0, ATMIZER II rev: 4
idb=0x63981E5C, ds=0x639894A0, vc=0x639EBDE0
slot 2, unit 1, subunit 0, fci_type 0x0056, ticks 31997
4000 rx buffers: size=512, encap=64, trailer=28, magic=4
Curr Stats:
VCC count: current=22, peak=22
AAL2 VCC count: 0
AAL2 TX no buffer count: 0
AAL2 RX no buffer count: 0
SAR crashes: Rx SAR=0, Tx SAR=0
rx_cell_lost=3, rx_no_buffer=0, rx_crc_10=0, rx_no_mem=0
rx_cell_len=0, rx_no_vcd=416311, rx_cell_throttle=0, tx_aci_err=0
Rx Free Ring status:
base=0x3D27C040, size=4096, write=872
Rx Compl Ring status:
base=0x7E4E1580, size=4096, read=1852
Tx Ring status:
base=0x3D7039C0, size=8192, write=416
Tx Compl Ring status:
base=0x0E4E95C0, size=4096, read=208
BFD Cache status:
base=0x639E5D60, size=6144, read=6143
Rx Cache status:
base=0x639DBC60, size=16, write=12
Tx Shadow status:
base=0x639DDCE0, size=8192, read=415, write=416
Control data:
rx_max_spins=54, max_tx_count=54, tx_count=1
rx_threshold=2667, rx_count=12, tx_threshold=4608
tx bfd write indx=0x10DF, rx_pool_info=0x639DBD00
Control data base address:
rx_buf_base = 0x0E28F6E0 rx_p_base = 0x63995580
rx_pak = 0x638DE034 cmd = 0x63994F40
framer = 0x6048145C framer_cb = 0x63995360
framer_base = 0x3D100000 pci_pa_stats = 0x7E169CA0
device_base[0] = 0x3D000000 device_base[1] = 0x3D400000
ssram_base[0] = 0x3D200000 ssram_base[1] = 0x3D600000
sdram_base[0] = 0x3D300000 sdram_base[1] = 0x3D700000
pa_cmd_buf[0] = 0x3D27FC00 pa_cmd_buf[1] = 0x3D67FC00
vcd_base[0] = 0x3D200000 vcd_base[1] = 0x3D618000
chip_dump[0] = 0x0E169CCC chip_dump[1] = 0x0E169DCC
sar_buf_base[0] = 0x3D324000 sar_buf_base[1] = 0x3D70C000
bfd_base[0] = 0x3D264000 bfd_base[1] = 0x3D600000
acd_base[0] = 0x3D222080 acd_base[1] = 0x3D638240
Bad particle count = 0
SAR AutoRecovery : Disabled
SAR AR rx stuck count=0 tx stuck count=0
rx_crashes =0 tx_crashes =0
Framer Information:
Framing mode: SONET (STS-3c)
No alarm detected
Facility statistics: current interval elapsed 497 seconds
sbip lbip lfebe pbip pfebe hcse
------------------------------------------------------------
35 0 0 0 130 54 0
sbip: Section BIP8
lbip: Line BIP8/24
lfebe: Line FEBE
pbip: Path BIP8
pfebe: Path FEBE
hcse: Rx Cell HCS Error
show interface atm
########################################################
ATM2/0 is up, line protocol is up
Hardware is ENHANCED ATM PA
MTU 4470 bytes, sub MTU 4470, BW 149760 Kbit/sec, DLY 80 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM, loopback not set
Encapsulation(s): AAL5
4095 maximum active VCs, 22 current VCCs
VC Auto Creation Disabled.
VC idle disconnect time: 300 seconds
0 carrier transitions
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 529419
Queueing strategy: Per VC Queueing
5 minute input rate 37000 bits/sec, 29 packets/sec
5 minute output rate 25000 bits/sec, 28 packets/sec
160541704 packets input, 20086527569 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
33 input errors, 33 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
159965106 packets output, 19847981033 bytes, 0 underruns
0 output errors, 0 collisions, 3 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
Can you find something strange than the CRC?
Thank you in advance
Danilo
