config 1812w

[jmuro]

Hi

We have some publics ips (146-150) and i would try to configure the router to work with diferent IP-PORT from outside to inside.

The router work fine with the ip asigned to Fethernet0 (146), but don´t work with the others ips.

How can i do this?

thanks

i send you my configuration

[Georg Pauwen]

Hola,

can you verify with your provider that this address space has actually been assigned to and is being routed to you ? It could very well be that your provider has given you 13.80.250.144/30, which would encompass the IP address of your FastEthernet interface, as well as the IP address of the next hop specified in your default route statment...

Regards,

GP

[jmuro]

Really the ips are other, Is a good simulation

Yes, actually we work with this provider.

FastEthernet0 13.80.250.146 255.255.255.248 (configuration file attached in the first message)

Nest hop 13.80.250.145

Do you speak spanish?

Thank´s

[Georg Pauwen]

Hello,

the configuration looks good and should work...just one thing:

ip route 0.0.0.0 0.0.0.0 DNS1.250.145

Is this actually part of the configuration ?

Regards,

GP

[jmuro]

No, really is ip route 0.0.0.0 0.0.0.0 XXX.XXX.250.145

Error changing de file

[spremkumar]

Hi

I feel you are pointing here about the translation defined between 192.168.0.20 13.80.250.149.

Can you revert whether 192.168.0.20 is up & running also whether you are able to ping 13.80.250.149 from outside world ?

Also getting any translation o/p when u issue show ip nat translation ??

regds

[jmuro]

I tried it " ip nat inside source static tcp 192.168.0.20 80 13.80.250.149 80 extendable" before " ip nat inside source static 192.168.0.20 13.80.250.149" but it didn´t work.

I try it now and it work, i don´t understand

[jmuro]

Hi

The NAT is OK.

But when the router is running for 10-20 minutes crash and lost the conection from Internet-Intranet or all conecctions Internet-Intranet/Intranet-Internet.

Any idea

Thank´s

[spremkumar]

Hi

Can you check out the show version o/p which can tell u the possible reason for the reload/crash..

Also if possible do post out the same here ..

Have you enabled logging to ur external syslog servers ?? if yes are you getting any logs related to the crash on the server ?

also did u try to check out whether any crash dump file is being dumped ??

regds

[jmuro]

Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.3(8)YI1

, RELEASE SOFTWARE (fc1)

Synched to technology version 12.3(10.3)T2

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by Cisco Systems, Inc.

Compiled Fri 22-Apr-05 18:57 by ealyon

ROM: System Bootstrap, Version 12.3(8r)YH5, RELEASE SOFTWARE (fc1)

ROM: Cisco IOS Software, C181X Software (C181X-ADVIPSERVICESK9-M), Version 12.3(

8)YI1, RELEASE SOFTWARE (fc1)

cisco_csd uptime is 1 hour, 49 minutes

System returned to ROM by power-on

System image file is "flash:c181x-advipservicesk9-mz.123-8.YI1.bin"

Cisco 1812W (MPC8500) processor (revision 0x300) with 118784K/12288K bytes of memory.

Processor board ID FHK092811QC, with hardware revision 0000

10 FastEthernet interfaces

1 ISDN Basic Rate interface

2 802.11 Radios

31744K bytes of ATA CompactFlash (Read/Write)

Configuration register is 0x2102

I don't think I have any loging feature enabled, could you let me know how to do it please?

Also, I haven't directly configured any direct storage to dump this file, again, how could I configure it?

Where should I look to find theses files?

Thank you very much !!

[jmuro]

Actually there are 2 servers conected to the router for 2 hours and all run fine.

I think that the problem is when there are any more pcs connected to the router.

Any idea?

Thank´s a lot

[spremkumar]

Hi

Do revert back whether u have manually reseted the router ???

also refer this link for more info in troubleshooting the router crashes..

http://www.cisco.com/en/US/products/hw/iad/ps397/products_tech_note09186a00800b4447.shtml

regds

[jmuro]

Manually